English
English
4 charging thE ModEl
Attention:
The battery and motor must cool down for 15 to 30 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Unplug the battery plug
(1B)
from the battery connection cable
(1F)
and switch off
the remote control. Remove the battery from the model
(4A)
. Plug the USB charger
into an open USB port
(4B)
. The status LED on charger starts to flash.
• Plug the white balancer plug into the charging socket of the charger, ensuring correct
polarity
(4C)
. The battery must be gently inserted into the charging socket – DO NOT
USE FORCE. If the battery is not correctly inserted into the charging socket, the battery
may become damaged and, under certain circumstances, cause injury.
• The status LED on the USB charger lights up continuously when the charging process
starts.
• The charging process lasts approx.150 minutes and must be continuously monitored.
The red LED on the charger goes out as soon as the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the USB
port once charging is complete.
The model can fly for approx. 5-7 minutes after a charge time of approx. 150
minutes.
Warning notice:
The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
2 rEMotE control
2A
No function
2B
No function
2C
Control for thrust and rotation
2D
Video button
2E
Power LED
2F
Antenna
2G
Turbo switch
2H
Flip button
2I
Control for forwards/backwards and
sideways flight
2J
Trim for forwards/backwards
2K
Trim for sideways
2L
ON/OFF switch
2M
Battery compartment cover
2N
Locking screw
2O
Opening lever for the battery
compartment
2P
Button for Headless Mode
3 insErting battEriEs (rEMotE control)
3B
Insert 4 x 1.5 V AA batteries
and pay attention to the
polarity specifications, as
indicated in the battery
compartment.
3A
To open the battery
compartment, unscrew the
locking screw
(2N)
counter-
clockwise and open the
battery compartment cover
(2M)
to the top by pressing
down the opening lever
(2O)
.
3C
Close the battery
compartment cover
and screw in the
locking screw
(2N)
clockwise.
• Never disassemble or alter the battery
contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they must
be discharged or their capacity must be
fully depleted. Cover exposed terminals
with adhesive tape in order to prevent
short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
Required batteries for the model:
Power supply:
Rated output:
1 x DC 7,4 V / 3 Wh
Batteries: 7,4 V
echargeable
LiPo battery (included)
Capacity: 400 mAh
Battery requirement for the
remote control:
Power supply:
DC 6 V
Batteries: 4 x 1.5 V “AA”
(not included)
USB charger:
Power supply: DC 5V via USB port,
500 mA or higher
Rated output: 2 x 4,2 V / 250 mAh max.
1 ModEl
1A
Camera
1B
Rotor shaft with main
gear wheel
1C
Rotors
1D
Fuselage cover
1E
Camera lens
1F
Battery connection
cable
1G
Battery compartment
1H
SD card slot
5 start prEparation
The model must be switched on first in order to connect it to the remote control. To
do this, push the battery into the battery compartment on the model and connect the
battery plug with the battery connection cable
(1F)
. Do not use force and ensure the
correct polarity
(5A)
. Then place the model on an even, flat and stable surface.
Before switching on the remote control, the control for thrust and rotation
(2C)
must
point down
(5B)
. To switch on the remote control, set the ON/OFF switch
(2L)
to ON
and move the control for thrust and rotation
(2C)
briefly all the way up and then back
down again. After approx. 3 seconds, the model activates and is ready for use.
Once you have finished flying, switch the model off first and then the remote control.
A A
A A
A A
A A
16
17
