4 START PREPARATION
INSTRUCTIONS FOR SAFE DRIVING
Fit the antenna
(2C)
in the antenna socket of the remote control and tighten
(4A)
. The remote control of the vehicle
switches on automatically when the control buttons are actuated. The remote control of the vehicle switches on
automatically when the joystick is actuated. That means that only the switch on the underside of the vehicle has to
be set to ON
(1D)
. The switch on the vehicle must be set to OFF after use. Otherwise, a drive command can acciden
tally be triggered, causing the vehicle to drive away on its own, which can lead to considerable damage. Pressing
the forwards/backwards button moves the model forwards or backwards
(4B)
. Pressing the left/right button on the
remote control during travel moves the model left or right
(4C)
.
GENERAL DRIVING TIPS:
• Always maintain visual contact with the vehicle and
do not look at the remote control!
• On initial driving attempts, there is a general tendency
toward excessive movements of the controls. Make
sure that you have sufficient room.
After a crash, always release the lever for forwards and
reverse travel immediately in order to prevent damage
to the electronics.
THE SUITABLE DRIVING ENVIRONMENT:
The location in which the vehicle is driven should fulfill
the following criteria:
1. It should be a location in which there is as much
open area as possible, without disruptive obstacles.
2. Make absolutely sure when starting that there are no
people or animals in the immediate vicinity.
3. Always watch the vehicle so that it does not drive
into the operator, other people or animals and inju
ries them.
TROUBLESHOOTING
Problem: The vehicle does not move.
Cause:
·
The batteries are too weak and/or depleted.
Remedy:
·
The batteries were possibly not inserted correctly. Please observe the polarity indication in the model
·
Please replace with new batteries.
Problem: Remote control does not work.
Cause:
1. The batteries were not inserted correctly.
2. The batteries do not have enough power.
Remedy:
1. Check whether the batteries are inserted correctly.
2. Please replace with new batteries.
Problem: The vehicle cannot be controlled with the remote control.
Cause:
1. The batteries are depleted.
2. The connection between the remote control and vehicle has been severed.
3. The antenna on the remote control has not been tightened.
Remedy:
1. Insert new batteries.
2. When the model is further than 10 metres away, move towards the model
3. Fit the antenna in the antenna socket of the remote control and tighten.
Additional tips and trick can be found online at
www.revell-control.de
.
Go to www.revell-control.de for ordering information
and tips on replacing spare parts, plus other useful
information on all Revell Control models.
www.revell-control.de
SERVICE NOTES
English
English
5 STEERING TRIM ADJUSTMENT
The correct trim is a basic requirement for faultfree driving behaviour from the vehicle. Adjusting the trim is
easy, but it requires a little patience and a feel for it. Please follow the following instructions precisely:
If the vehicle pulls to the left or right while driving without steering...
use the straightahead trimming
(1A)
to correct the wheel alignment by turning it in the opposite direction.
The wheel alignment can be found on the bottom of the vehicle
(cf. 5)
.
20
21
Содержание Control Junior 23013
