manualshive.com logo in svg

Repotec RP-G802W, Руководство пользователя

Поделиться
Скачать
Repotec RP-G802W Скачать руководство пользователя страница 24

          

                 

Easy Smart GbE Switch   

 

 

 

3. The switch will be restarted directly in about 20 seconds without any successful page. 

 

 

3.3 MultiCast 

 

Internet Group Management Protocol (IGMP) snooping is a multicast control mechanism, which 

can be used on the switch for dynamic registration of the multicast group.   

Internet Group Management Protocol (IGMP) snooping allows a switch to forward multicast traffic 

intelligently on the switch. This feature prevents the switch from broadcasting the traffic to all ports 

and possibly affecting network performance. 

 

3.3.1 IGMP Snooping 

 

Click 

System

 > 

MultiCast 

> 

IGMP Snooping

 

On this page user can enable or disable IGMP snooping feature.   

 

 

 
The following table describes the labels in this screen. 

 

LABEL 

 

DESCRIPTION 

 

IGMP Snooping 

Enable or Disable IGMP snooping function globally on the switch. 

Apply   

Click

 Apply

 to make the settings take effect immediately. 

 

 

 

23 

 

Содержание RP-G802W












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды