manualshive.com logo in svg

Repotec RP-G802W, Руководство пользователя

Поделиться
Скачать
Repotec RP-G802W Скачать руководство пользователя страница 13

          

                 

Easy Smart GbE Switch   

 

Chapter 3   System 

The System page is mainly for system configuration of the switch, including management , 

maintenance and multicast setting for the switch. 

 

3.1 Management 

Use the Management pages to view switch information and configure some settings for ports, trunk 

group and EEE. 

 

3.1.1 Switch Information 

 

Click 

System 

>

 Management 

>

 Switch Information

 

On this page user can configure and browse some switch information such as Switch name, MAC 

address, IP address, Gateway and Firmware Version and so on. 
 

 

  With editable textbox in the table

，

user could configure the field value. 

LABEL 

DESCRIPTION 

Switch Name 

Name of the switch, can be modified for identifying other different 
switches.   

MAC Address 

Displays the MAC address of the switch. 

Firmware Version 

Displays the installed software version number. 

DHCP Client 

Displays the status of the DHCP function for the switch.

 

IP Address 

Displays the system IP address of the switch 

Subnet Mask 

Displays the subnet mask of the switch.   

Gateway 

Displays the gateway IP Address of the switch.   

Apply 

Click

 Apply

 to make the settings take effect. 

 

3.1.2 IP Address Setting 

 

 

12 

 

Содержание RP-G802W












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды