Renovo Digiwatts RN5000US Скачать руководство пользователя страница 49

Страница: 49 / 58

Installation Guide RN5000US

7 Displays and Messages

Each Digiwatts inverter comes equipped with three LED status indicators.

This shows

users the main status when the inverter is working.

The basic definitions of the indicator lights are as follows:

Figure 7-1 Front Cover LED Status Indicators

The upper green LED indicates the Digiwatts unit is waiting, and the middle green

LED indicates the Digiwatts unit is running.

The red LED indicates the status of stop.

It means that there is some fault, either

inside the inverter or somewhere in the PV system.

The inverter will not operate

until the fault has been corrected.

7.1 LED Operation Indicators

Night

All LEDs are off.

The inverter is in standby mode because the input voltage is too low for operation.

Initialization

All LEDs are on.

The inverter is initializing.

The power from the array is sufficient to initialize control

Содержание Digiwatts RN5000US



























































Результаты поиска

Содержание Digiwatts RN5000US

Отзывы:

Похожие инструкции для Digiwatts RN5000US

Бренды по названию

Популярные бренды

Renovo Digiwatts RN5000US, Руководство по установке

Результаты поиска

Содержание Digiwatts RN5000US

Отзывы:

Похожие инструкции для Digiwatts RN5000US

Бренды по названию

Популярные бренды