manualshive.com logo in svg

Renesas OB1203, Руководство пользователя

Поделиться
Скачать
Renesas OB1203 Скачать руководство пользователя страница 4

OB1203 Certification Preparation, Setup, and Test Procedure

 

 

X0119984   Rev.1.0 
Mar 11, 2021 

 

Page 4  

 

 

 

Figure 4. Top View of the OB1203 

to WhaleTeq Test Adapter 

 

 

Figure 5. Side View of OB1203 to 

WhaleTeq Test Adapter 

 

 

Figure 6. Perspective View of 

OB1203 to WhaleTeq Test Adapter 

 

The 3D stl file can be printed on a 3D printer (see 

OB1203SD-RL-EVK

 webpage for file).  

It is also required to apply (at least on one side of the test adapter) a reflective insert ensuring acceptable optical 
performance, and at the same time, eliminating uncertainty from the print quality and/or material properties. It 
has been determined that aluminum foil is a good material for this purpose, and Renesas has provided an 
applicator to insert the foil properly. This applicator can also be 3D printed.  

 

Procedure to Insert the Aluminum Foil Using the Applicator

 

1.  Use an appropriately sized piece of Aluminum foil and wrap it around the 
pointed end of the applicator in a single ply. 

2.  Insert the Aluminum foil into one cavity of the adapter making sure the 
applicator fits snuggly into the cavity – use firm but light pressure.  

3.  Remove the applicator 

and

 the Aluminum foil from the cavity.  

4.  Use a sharp knife and cut off the excess of the Aluminum foil just above the 
cone – there should be a small cutting groove to assist a straight cut (see Figure 8 
image on top left).  

5.  Apply a thin layer of glue to the outside of the Aluminum foil and re-insert the 
Aluminum foil using the applicator tool.  

6.  This time, remove the applicator leaving the Aluminum foil behind in the cavity. 
It should be held in place by the glue. 

7.  Using a small tool, clear the optical opening at the tip of the adapter of the 
Aluminum foil and 3D print material ensuring an un-obstructed path for the optical 
signal.  

 

Note

: The cavity with the Aluminum foil should be used on the Photo Detector 

receiver side of the DUT and the LED side of the WhaleTeq test head to collect 
the maximum light possible and funnel it into the DUT receiver.  

 

DUT OB1203 

DUT OB1203 

DUT OB1203 

Renesas Test 
adapter 

WhaleTeq  
Test head 

Figure 7. Illustration of 

Applicator Inserted into Test 

Adapter 

Figure 8. Illustration of 

Cutting Groove 

Содержание OB1203




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды