background image

Environmental Compliance and Certifications: 

• 

Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC 

WEEE Marking Notice

 (European Union Only)

 

 

Renesas development tools and products are directly covered by the European 

Union's Waste Electrical and Electronic Equipment, (WEEE), Directive 
2002/96/EC. As a result, this equipment, including all accessories, must not 
be disposed of as household waste but through your locally recognized 
recycling or disposal schemes. As part of our commitment to environmental 
responsibility Renesas also offers to take back the equipment and has 
implemented a Tools Product Recycling Program for customers in Europe. 
This allows you to return equipment to Renesas for disposal through our 
approved Producer Compliance Scheme. To register for the program, click 
here “

http://www.renesas.com/weee

". 

 

United States Regulatory notices on Electromagnetic compatibility 

FCC Certifications (United States Only): 

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in a 
commercial environment. This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the instruction manual, may cause 
harmful interference to radio communications. Operation of this equipment in a residential 
area is likely to cause harmful interference in which case the user will be required to 
correct the interference at his own expense. 

CAUTION:  

Changes or modifications not expressly approved by the party 

responsible for compliance could void the user's authority to operate 

the equipment. 

Содержание H8S/2400 Series































Отзывы: