Renault LAGUNA 2000 Скачать руководство пользователя страница 28

Страница: 28 / 84

VALUES AND SETTINGS

Procedure for tensioning the timing belt

07-11

F9Q engine

Refit the pin

Mot. 1054

and set the timing at its setting

point,

(begin to press on the pin a half-tooth before

alignment of the mark on the camshaft pulley and
that made by the operator on the inner timing
housing, to prevent it falling into a crankshaft
balance hole).

Remove the pin

Mot. 1054

Apply pretension between the crankshaft timing
sprocket and the tensioner using the tool

Mot. 1543

and the cover

, adjusting the torque wrench to a

torque of

1.1 daNm.

Connect the sensor of

Mot. 1505.

Check that the tension value is 85

3Hz, readjust it

if necessary.

Tighten the tension wheel nut to a torque of

5 daNm.

NOTE: it is vital that you tighten the tensioner nut
to torque to avoid any loosening which may cause
damage to the engine.

WARNING: remove the washer numbered 4
included in the tool kit Mot 1543 before fitting the
crankshaft pulley.

Содержание LAGUNA 2000





















































































Результаты поиска

Содержание LAGUNA 2000

Отзывы:

Похожие инструкции для LAGUNA 2000

Бренды по названию

Популярные бренды

Renault LAGUNA 2000, Руководство пользователя

Результаты поиска

Содержание LAGUNA 2000

Отзывы:

Похожие инструкции для LAGUNA 2000

Бренды по названию

Популярные бренды