Renault LAGUNA 2000 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 84

background image

VALUES AND SETTINGS

Procedure for tensioning the timing belt

07

07-16

K4M engine

2

nd

PROCEDURE

The second procedure is used for the replacement
of all components requiring the slackening of one
or more of the camshaft pulleys.

All the camshaft nuts must be replaced during this
operation.

Adjusting the timing

WARNING: it is essential to degrease the
following: the end of the crankshaft (timing side),
the bore of the timing pinion, the bearing faces of
the accessories belt as well as the ends of the
camshafts (timing side) and the bores of the
camshaft pulleys, to prevent there being any slip
between the timing, crankshaft and camshaft
pulleys which would risk destroying the engine.

Position the camshaft grooves, as illustrated below, by
tightening the two old camshaft pinion nuts on the
studs at the end of the camshafts.

Fit tool

Mot. 1496

, on the end of the camshafts.

Position the camshaft pulleys pretightening the new
nuts

(without locking the nuts, clearance between

the nut and pulley of 0.5 - 1 mm).

Check that the crankshaft is resting on the Top Dead
Centre pin (crankshaft groove (5) upwards).

«
...
31
32
33
34
35
...
»

Содержание LAGUNA 2000





















































































Отзывы:

Нет отзывов

Похожие инструкции для LAGUNA 2000

Бренд: M7 SPEED Страницы: 11

Sprinter Bed System Adventure Wagon Kit

Бренд: FVC Страницы: 8

Бренд: DEFA Страницы: 9

Slim Line LED Light Grille Kit

Бренд: rough country Страницы: 8

Бренд: Code 3 Страницы: 8

Бренд: Motoalliance Страницы: 8

Бренд: Demco Страницы: 4

Бренд: Thule Страницы: 4

nERGY ETSA200R-PA

Бренд: Soundoff Signal Страницы: 3

Бренд: Truma Страницы: 10

Бренд: Whispbar Страницы: 14

Бренд: Car-Interface Страницы: 23

Бренд: SSV Works Страницы: 2

T13 Outback Frontal Protection System

Бренд: T.J.M. Страницы: 18

Бренд: Audi Страницы: 4

Бренд: ACV Страницы: 2

Бренд: HUSKY LINERS Страницы: 4

Бренд: iOttie Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды