Renault LAGUNA 2000 Скачать руководство пользователя страница 32

Страница: 32 / 84

VALUES AND SETTINGS

Procedure for tensioning the timing belt

07-15

K4M engine

Checking the tension and the timing.

Checking the tension

Turn the crankshaft clockwise twice (timing end), and
before the end of the second turn, tighten the pin

Mot. 1489

in the cylinder block and move the

crankshaft slowly and smoothly to rest on the pin.

Remove the Top Dead Centre pin.

Check that the pulley indices are aligned, otherwise
continue with the tensioning procedure.

Checking the timing

Ensure that the tension wheel indices are in the
correct position before checking the setting of the
timing.

Tighten the pin

Mot. 1489

in the cylinder block and

move the crankshaft slowly and smoothly to rest on
the pin.

Fit (without forcing) tool

Mot. 1496

for setting the

camshaft (the camshaft grooves must be horizontal).

The timing setting and tensioning operation must
be repeated if the tool does not engage.

Содержание LAGUNA 2000





















































































Результаты поиска

Содержание LAGUNA 2000

Отзывы:

Похожие инструкции для LAGUNA 2000

Бренды по названию

Популярные бренды

Renault LAGUNA 2000, Руководство пользователя

Результаты поиска

Содержание LAGUNA 2000

Отзывы:

Похожие инструкции для LAGUNA 2000

Бренды по названию

Популярные бренды