manualshive.com logo in svg

Renault LAGUNA 2000, Руководство пользователя

Поделиться
Скачать
Renault LAGUNA 2000 Скачать руководство пользователя страница 31

VALUES AND SETTINGS

Procedure for tensioning the timing belt

07

07-14

K4M engine

Refit:
– the timing belt,
– the pulley by tightening the mounting bolt using 

Mot. 1368 

(to a torque of 

4.5 daNm

 for information 

only).

Belt tension

Shift the adjustable tension wheel index (A') by 

7 to 

8 mm

 beyond the fixed index (7), using a 

6 mm

 Allen 

key (in B).

NOTE:

 position (A) corresponds to the adjustable 

index at rest.

Pre-tighten the tension wheel nut to a torque of

 

0.7 daNm.

Fit the crankshaft accessories pulley by moving the 
bolt away from the pulley (

2 to 3 mm

 clearance 

between the bolt and the pulley).

NOTE:

– the crankshaft accessories pulley bolt can be reused 

if the length under its head does not exceed 

49.1

 

mm

 

(otherwise replace it),

– do not oil the new bolt. However, bolts must be oiled 

if they are being reused.

Tighten the crankshaft pulley bolt to a torque of 

2 daNm

 then angle tighten to 

135

°

 

±

 

15

°

 (crankshaft 

resting on the Top Dead Centre pin ).

Remove tool 

Mot. 1496 

for clamping the camshaft and 

Mot. 1489

 Top Dead Centre pin.

Turn the crankshaft clockwise twice (timing end), and 
before the end of the second turn, tighten the pin 

Mot. 1489

 in the cylinder block and move the 

crankshaft slowly and smoothly to rest on the pin.

Remove the Top Dead Centre pin.

Slacken the tension wheel nut by a maximum of one 
turn, holding it with a 

6 mm

 Allen key.

Align the adjustable index with the fixed index and 
tighten the nut fully to a torque of

 2.7 daNm.

Содержание LAGUNA 2000





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды