background image

 

 
 

Function description 

 

 

28 

4.8  High-frequency (HF) ignition 

The  push  button  [11]  is  used  to  select  the  HF  arc  ignition  for  TIG  welding, 
whereby the LED display shows whether the high frequency is on or off. 

4.8.1  Welding with HF ignition  

REHM  TIG  welding  machines  are  equipped  with  RF  igniter.  HF  ignition    is 

automatically switched off in the "electrode" setting. 

HF  ignition  makes  contact-free  ignition  of  the  arc  between  the  electrode  and 
workpiece through pre-ionization of the air gap for DC and AC welding possible, 
whereby  tungsten  inclusions  and  therefore  welding  defects  are  prevented.  In 
either case, the HF ignition unit is automatically switched off again after ignition. 
Re-ignition of the arc described in Section 4.6.15 when AC welding is performed 

without using the HF ignition unit. This reduces the electrical noise emission and 
even enables AC welding without HF ignition, as is already known for DC welding 
(see Section 4.8.2). 

The  RF  igniter  is  operational  when  set  to  RF  On  " ".  To  ignite  the  arc,  the 
electrode  is  kept  approx.  3-5  mm  above  the  workpiece.  By  actuating  the  torch 
trigger the path is ionized by a high-voltage pulse and arcing occurs. Contactless 
ignition enables the prevention of tungsten inclusions in the welded seam. When 
welding the HF ignition is automatically switched off after ignition. 

4.8.2  Welding without HF ignition  

When  welding  with  direct  or  alternating  current  contact  ignition (lift  arc  ) can  be 
used. For this the high frequency is turned off. To ignite the arc, the electrode is 
placed  on  the  workpiece  and  the  torch  trigger  actuated.  On  lifting  the  electrode 
the  arc  program-controlled  ignition  takes  place  without  wear  occurring  to  the 
pointed  electrode.  This  option  can  be  used  to  advantage  when  working  on 
sensitive  electronic  devices  (for  example,  in  hospitals,  repair  welding  on  CNC 
machines),  where  there  is  the  risk  of  interference  originating  from  high  voltage 
pulses. 

4.9 

“Pulsing

 

The  push button  [16]  is  used  to  select  the  welding process without  pulses, with 
conventional pulses and with high-frequency pulses, whereby the LEDs indicate 
the selected pulse type by illuminating. 

 

Содержание TIGER 180 AC/DC ULTRA





































































Отзывы: