Regency U31-LP10 Скачать руководство пользователя страница 19

Страница: 19 / 36

Regency U31-10 Gas Fireplace Insert

installation

Diagram 4

Diagram 5

Rear View: Trim Assembly

Diagram 2

Diagram 3

Rear View: Faceplate Assembly

Diagram 1

STANDARD FACEPLATE &

HEARTH TRIM INSTALL

Lay the faceplate panels flat, face down

on something soft so they don't scratch.

2) Take the top faceplate and align the holes in

it with the holes in the side panels. Using the

screws provided, attach from the top of the

panel (the holes in the top panel are slightly

larger than the holes in the side panel to

facilitate easier installation). Diagram 1.

Hint: Don't tighten the screws down completely

at this point, continue on with steps 3 and 4

and do a trial fit to the unit. Make any neces-

sary adjustments and when it fits properly

then tighten down the screws.

Hearth Trim Option: Hearth Trim is an

option that can be used to finish off the

installation when the bottom of the fireplace

is higher than the hearth or to raise the fire-

place. Attach the Hearth Trim to the bottom

of the faceplate side panels with the screws

provided. See Diagram 1.

3) Using the connectors provided, join the left

side trim (with the ON/OFF switch) to the

top trim. Diagram 2. Connect the right side

trim to the top trim.

4) Place the trim on the assembled faceplate

panels, aligning the wire connections from

the switches with the notch on the left side

panel.

5) Connect the fan switch wires by taking the

black and red wires with the male ends (in

the grey harness) and connect them with the

wire connectors from the fan speed control.

6) Connect the ON/OFF switch wires by taking

the black and red wires with the female ends

and connect them to the ON/OFF switch.

7) Tuck the wires into the faceplate to keep them

away from the insert using the clip provided.

Attach the clip to the rear of the faceplate to

ensure that the wires do not touch the side

of the unit. Diagram 3.

8) The power cord should be run behind the

faceplate panel.

9) Attach the brass trim to the faceplate by

drilling a 1/8" hole through into the faceplate

using the hole in the trim as a guide. Fasten

the trim to the faceplate panels using the

plated screws. Diagram 4.

10) Attach the faceplate panels to the insert

body using the 4 remaining black screws.

Diagram 5.

11) Push the Regency logo plate into the two

holes in the bottom left corner of the face-

plate.

Содержание U31-LP10





































Результаты поиска

Содержание U31-LP10

Отзывы:

Похожие инструкции для U31-LP10

Бренды по названию

Популярные бренды

Regency U31-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание U31-LP10

Отзывы:

Похожие инструкции для U31-LP10

Бренды по названию

Популярные бренды