Regency L234-LP10 Скачать руководство пользователя страница 17

Страница: 17 / 48

Liberty

L234-10 Direct Vent Gas Insert

installation

CONVERSION FROM NG TO LP

919-465

11.30.16

L234-10 / L234-11

CONVERSION KIT #537-969 FROM NG TO LP

LP Conversion Kit Contains:

Qty. Part #

Description

1 910-037

LP Pilot Oriﬁ ce

1 904-163

Oriﬁ ce #54

1 904-529

5/32" Allen Key

1 910-582

Stepper Motor

1 918-590

LP Conversion Decal

1 908-528

Red Propane Label

1 919-465

Instruction Sheet

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER, IF IN DOUBT DO NOT DO THIS CONVERSION!!

LP Conversion Instructions

Shut oﬀ gas and electrical supply to the unit.

Remove the faceplate.

Remove the safety screen and glass door

- see manual for detailed instructions.

Remove the logs if installed.

Remove the brick panels if installed.

Remove the burner by undoing the 3 screws.

Burner Removed

Remove the burner tray by undoing the 4

screws.

Burner Tray Removed

Remove burner oriﬁ ce with a 1/2" wrench

and discard.

Install the new LP burner oriﬁ ce stamped

#54 and tighten.

10.

Pull oﬀ the pilot cap to expose the pilot

oriﬁ ce.

11.

Unscrew the pilot oriﬁ ce with the supplied

allen key and replace it with the LP pilot

oriﬁ ce in the kit and re-install the pilot cap.

12.

Remove the pilot/on/oﬀ extension knob by

pulling the knob towards you. Remove NG

stepper motor by removing 3 screws in loca-

tions shown below–replace with LP stepper

motor, secure in place with 3 screws.

Remove NG Stepper motor and

replace with LP Stepper motor

13.

Reinstall the pilot/on/oﬀ extension knob

removed from step 12. Check for gas leaks

with a proper soapy solution or leak detector.

14.

Check inlet and outlet pressures. Refer to

"Gas Pipe Pressure Testing" section of the

manual.

15.

Attach the label "This unit has been con-

verted to LP" near or on top of the serial #

decal.

16.

Replace yellow "NG" label with red "LP"

label.

17.

Reverse Steps 8 - 1.

NOTE

: before re-installing burner, check the LP

aeration settings.

18.

Check operation of ﬂ ame control.

19.

Check for proper ﬂ ame appearance and

glow on logs.

Содержание L234-LP10

















































Результаты поиска

Содержание L234-LP10

Отзывы:

Похожие инструкции для L234-LP10

Бренды по названию

Популярные бренды

Regency L234-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание L234-LP10

Отзывы:

Похожие инструкции для L234-LP10

Бренды по названию

Популярные бренды