Regency HZI540PB Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 56

background image

L540PB-2 / HZI540PB-2 Direct Vent Gas Insert

33

INSTALLATION

L540PB Brick Panel Installation
Video

BRICK PANEL INSTALLATION

Brick panels are soft and fragile. Use caution when handling the panels,

being careful not to jar them or scratch the painted surfaces.

7)

Once one Brick Panel is installed, you can release the Brick Panel Rear.

The side Liner will hold the rear Liner in place. Install the Brick Panel Left
the same way you installed the Brick Panel Right. Both side liners should
be just slightly back from the front edge of the Firebox.

8)

Snug the Brick Panel Retainers up against the Brick Panel Left & Right.

Using a screw driver, secure the screws that hold down each retainer.

9)

Reinstall burner - see ceramic burner installation section in manual.

Upper Left of Firebox

Exhaust Baffle

Firebox Liner Left

Lower Right of Firebox

Firebox Liner
Retainer (x2)

Firebox Liner Right

3)

Using a screw driver, loosen the fasteners holding the Brick Panel Re-

tainers and move them towards the center of the fi rebox. -see Diagram 1.

4)

Remove the brick panels from their packaging. Inspect them prior to

installation to make sure they haven`t been damaged during shipping.

5)

Install the rear brick panel, by placing it against the rear of the fi rebox.

The bottom of the brick panel rests on a small sheet metal lip, just above
the air intake at the bottom rear of the Firebox. You will need to hold this
panel in place while you install the right brick panel. Do not let go of the
panel or it may fall forward and be damaged.

6)

While holding the rear brick panel in place, slide the right along the side

of the fi rebox toward the rear of the fi rebox. Each side Brick Panel will
sit upon a Brick Panel Retainer and the top will be held between the
Exhaust Baffl e and the side of the fi rebox.

2)

Lift the Burner slightly while pulling forward to clear the mixing tube.

1)

Remove fi ller sections from right and left sides of the burner and discard

- see below.

Filler section

«
...
31
32
33
34
35
...
»

Содержание HZI540PB

























































Отзывы:

Нет отзывов

Похожие инструкции для HZI540PB

Бренд: Quadra-Fire Страницы: 28

Бренд: Magiglo Страницы: 48

Бренд: Valcourt Страницы: 44

Бренд: Majestic Страницы: 76

Antigua PIT1015A

Бренд: Safavieh Furniture Страницы: 3

Ofiretable43-BK

Бренд: Ohana Страницы: 22

Бренд: Palazzetti Страницы: 36

Бренд: Napoleon Страницы: 4

Бренд: Infinity Страницы: 32

Superior Fireplaces DRT2000 Series

Бренд: IHP Страницы: 76

Fireplace Glass Door

Бренд: pleasant hearth Страницы: 27

Бренд: Comfort Glow Страницы: 16

Brann table corten

Бренд: Forno Страницы: 6

Бренд: Mainstays Страницы: 76

Бренд: Majestic Страницы: 70

Бренд: UKIAH Страницы: 24

Бренд: Blumfeldt Страницы: 36

Бренд: Napoleon Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды