Regency HZ42STE Скачать руководство пользователя страница 9

Страница: 9 / 60

Regency Horizon™ HZ42STE-10 Gas Fireplace

installation

This includes:

Clocking the appliance to ensure the correct

firing rate (rate noted on label 26,000 Btu/h

(NG), after burning appliance for 15 minutes.

If required, adjusting the primary air to ensure

that the flame does not carbon. First allow the

unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that

causes sooting or carboning that results in dam-

age is not the responsibility of the manufacturer.

INSTALLATION CHECKLIST

Locate appliance

a) Room location (Refer to "Locating Your

Gas fireplace" section)

b) Clearances to Combustibles (Refer to

"Clearances" section)

c) Mantle Clearances (Refer to "Mantel

Clearances" section)

d) Framing & Finishing Requirements (Refer

to "Framing & Finishing" section)

e) Venting Requirements (Refer to "Venting"

section)

Assemble Top and Side Standoffs (Refer to

"Unit Assembly Prior to Installation).

Slide unit into place.

Install vent (Refer to "Venting Arrangement"

sections).

Make gas connections (Refer to "Gas Line

Installation section).

Make electrical connections to receptacle

supplied with unit (recommended).

Install 4 AA batteries into receiver/switch box

or use AC power adaptor supplied with this

appliance.

See remote control instructions for operation

Test the pilot (Refer to "Pilot Adjustment" section).

10)

Test Gas Pressure (Refer to "Gas Pipe Pressure

Testing" section).

11)

Install standard and optional features. Refer

to the following sections:

Glass Crystals/ Firebeads /Optional

Ceramic Stones

Optional Firebox Base Pebbles

Optional Reflective Panels

Inner door Frame

Faceplate

Remote Control or Wall Thermostat

12)

Final check.

Before leaving this unit with the customer, the

installer must ensure that the appliance is firing

correctly and

operation fully explained to

customer

LOCATING YOUR

GAS FIREPLACE

When selecting a location for your fireplace,

ensure that the clearances are met as outlined

in the "Clearances" section.

Provide adequate clearances for servicing.

The appliance must be installed on a flat, solid,

continuous surface (e.g. wood, metal, concrete).

This may be the floor, or raised up on a platform

to enhance its visual impact. If the appliance is

going to be installed on carpeting, combustible

linoleum tile or other combustible material other

than wood flooring, the appliance must be

installed on a metal or wood panel extending

the full width and depth of the appliance.

The Direct Vent Gas Fireplace can be installed

as follows:

Model #

Position

HZ42STE:

See Thru

HZ42STE:

See Thru

This appliance is Listed for bedroom installations

when used with a Listed Millivolt Thermostat.

Some areas may have further requirements,

check local codes before installation.

The HZ42STE Direct Vent Gas Fireplace is

approved for alcove installations, which meet

the clearances listed on this page.

We recommend that you plan your installation on

paper using exact measurements for clearances

and floor protection before actually installing this

appliance. Have a qualified inspector, dealer, or

installer review your plans before installation.

Note: For Exterior Vent Termination

Locations see section "Exterior Vent

Termination Locations."

Glass

36" min.

(914mm)

36" min.

(914mm)

Glass

36"min.

(914mm)

36"min.

(914mm)

36"min. walkway (914mm)

Glass

HZ42 ST - SEE THRU

See mantel clearances

Содержание HZ42STE





























































Результаты поиска

Содержание HZ42STE

Отзывы:

Похожие инструкции для HZ42STE

Бренды по названию

Популярные бренды

Regency HZ42STE, Инструкция для владельца и по установке

Результаты поиска

Содержание HZ42STE

Отзывы:

Похожие инструкции для HZ42STE

Бренды по названию

Популярные бренды