manualshive.com logo in svg

Regency City CC40LEPV-LP, Инструкция для владельца и по установке

Купите газовую плиту Regency City CC40LEPV-LP и получите бесплатно руководство по эксплуатации и установке. Скачайте свой пользовательский мануал совершенно бесплатно с нашего сайта. Не упустите возможность быть в курсе всех особенностей этой удивительной модели!

Поделиться
Скачать
background image

 

City Series CC40EPV

  |    5

safety decal

This is a copy of the label that accompanies Direct Vent Gas 
Fireplace. We have printed a copy of the contents here for your 
review. The safety label is located on the front inside base of 
the unit, visible when the outer front panel is removed.

NOTE: Regency

®

 units are constantly being improved. Check 

the label on the unit and if there is a difference, the label on 
the unit is the correct one.

Copy of Safety Decal

For the State of Massachusetts, installation 
and repair must be done by a plumber or 
gas fitter licensed in the Commonwealth of 
Massachusetts.

For the State of Massachusetts, flexible con-
nectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appli-
ances individual manual shut-off must be a 
t-handle type valve.

The  State  of  Massachusetts  requires  the 
installation of a carbon monoxide alarm in 
accordance with NFPA 720 and a CO alarm 
with battery back up in the same room where 
the gas appliance is installed.

Part #:   

919-919a

Colour:  

Black on grey except what is indicated as being printed red.

Size:   

(File at 100%)  9.3"w x 5.7"h

Material:  

Start serial sequence @ 477000001

Oct. 10/18: 

Created draft

Nov.21/18: 

Added efficiencies as per R/D

Jan. 29/19: 

Remodeled decal + added ETL logo at the bottom

DO NOT REMOVE THIS LABEL /

NE PAS ENLEVER CETTE ÉTIQUETTE 

                     

477

477

DOOR SEAL: Please 

check that the door is 

properly sealed

FPI Fireplace Products International Ltd. Delta, BC, Canada

Minimum Clearances to Combustibles /

Dégagements minimaux par rapport aux matériaux combustibles

Serial No./ No de série

MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.

Listed/Nom:

 VENTED GAS FIREPLACE  / FOYER AU GAZ À ÉVACUATION

Certified to/Certifi  : 

é

 ANSI Z21.88-2017 • CSA-2.33-2017

                                     CSA 2.17-2017

                    

Electrical supply / Alimentation électrique  115VAC, 1.5 A, 60Hz.

   

Made in Canada/ Fabriqué au Canada

Duplicate S/N

(

See instruction manual for detailed instructions)

(Voir manuel pour plus de détails)

GAZ PROPANE : Modèle

 

CC40LEPV-LP/CC40REPV-LP 

PROPANE GAS: Model: CC40LEPV-LP/CC40REPV-LP

       

Minimum supply pressure

Manifold pressure - High

Manifold pressure - Low

Orifice size

Maximum input

Minimum input

Altitude

GAZ NATUREL : Modèle 

CC40LEPV-NG/CC40REPV-NG

 

5.0"           WC/C.E.   (1.25 kPa)

3.8"           WC/C.E.   (0.94 kPa)

1.1"        WC/C.E. (0.27 kPa)

# 42                     DMS      

28,500   Btu/h  (8.33 kW)

15,500   Btu/h  (4.54 kW)

0-4500       ft/pi          (0-1372 m)

11"       WC 

   (2.73 kpa)

10.5 "     WC/C.E.   (2.62 kPa)

2.9"       WC/C.E.  (0.72 kPa)

# 53                   DMS   

28,500  Btu/h  (8.35kW)

15,500  Btu/h  (4.54 kW)

0-4500      ft/pi         (0-1372 m)

         

Minimum supply pressure

Manifold pressure - High

Manifold pressure - Low

Orifice size

Maximum input

Minimum input

Altitude

Side Walls / Murs latéraux

A 

36” (914 mm)

Ceiling / Plafond

B              37-1/2”  (953 mm)

Min. Mantel Height

 

/Hteur Min 

Manteau

C 

9"  (229 mm)

Max. Mantel Depth/Profondeur Max 

Manteau

D 

12”  (305 mm) 

Alcove Width/Largeur Alcôve

E 

84"  (1524 mm)

Alcove Depth/Profondeur Alcôve

F 

36"  (2134 mm)

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1.

This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the 

United States, or when such a standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI  A119.2 ou NFPA 501C Standard for Recreational Vehicles

This appliance is only for use with the type(s) of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by 

local codes. See owner's manual for details. This appliance is supplied with a conversion kit.

L'appareil doit être installé conformément aux codes et règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation National Fuel Gas Code ANSI Z223.1, ou CSA-B149.1 Natural Gas and 

Propane Installation Code en vigueur.

L'appareil doit être installé conformément à la norme CAN/CSA-Z240, Série MM, Maisons mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction 

and Safety Standard. Si ces normes ne sont pas applicables, veuillez vous référer à la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C 

Standard for Recreational Vehicles.

Cet appareil doit être utilisé uniquement avec les types de gaz indiqués sur la plaque signalétique et peut être installé dans une maison préfabriquée (É.-U. seulement) ou mobile installée à demeure si les règlements 

For Use Only with Barrier CC40LEPV - Left Corner (Part # 940-485/P,940-440/P) & CC40REPV Right Corner (Part # 940-485/P,940-439/P) Follow installation instructions. 

Utiliser uniquement avec l’écran CC40LEPV -Coin gauche (n°940-485/P,940-440/P) & CC40REPV - Coin droit (n°940-485/P,940-439/P) . Suivre les instructions d'installation.

Pression d'alimentation minimale

Pression de sortie (manifold) - Haute

Pression de sortie (manifold) - Basse

Taille de l’orifice

D bit calorifique maximal 

é

D bit calorifique minimal

é

Altitude

Pression d'alimentation minimale

Pression de sortie (manifold) - Haute

Pression de sortie (manifold) - Basse

Taille de l’orifice

D bit calorifique maximal

é

D bit calorifique minimal

é

Altitude

VENTED GAS FIREPLACE  - NOT FOR USE WITH SOLID FUELS. 

NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE. 

FOYER AU GAZ À ÉVACUATION - 

Part No. 946-556 Heatwave Kit may be used.   La trousse Heatwave (pièce n°946-556) peut être utilisée

.

Model/Modèle :       

CC40LEPV-NG

  

   

CC40LEPV-LP

      

 

CC40REPV-NG

     

 

CC40REPV-LP  

     

FOR USE WITH GLASS DOORS CERTIFIED WITH THE APPLIANCE ONLY      À UTILISER AVEC LES PORTES VITRÉES HOMOLOGUÉES POUR L'APPAREIL 

C #: 4001172

Refer to Intertek's Directory of Building Products for detailed information.

Pour plus de détails, se reporter au Répertoire des produits de construction de Intertek. 

J

B

C

D

H

A

E

F

                    

919-919a

CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1

Natural Gas / Gaz naturel 60.02%

Propane Gas / Gaz propane 60.85%

CANADIAN ENERGY 

PERFORMANCE 

VERIFIED

RENDEMENT 

ÉNERGÉTIQUE 

VÉRIFIÉ

EP5011169

NATURAL GAS: Model: CC40LEPV-NG/CC40REPV-NG

Decal Location

Remove barrier glass from unit (refer to manual) 
lift out the outer liner base glass once the glass 
has been removed the rating plate will be attached 
to a small black chain as seen below.

DO NOT REMOVE DECAL FROM UNIT

Содержание City CC40LEPV-LP

























































































Отзывы:

Нет отзывов

Похожие инструкции для City CC40LEPV-LP

Valor G3 Series Installation Instructions preview
G3 Series
Бренд: Valor Страницы: 4
Valor Retrofire RF24XBN Installation Manual And User'S Manual preview
Retrofire RF24XBN
Бренд: Valor Страницы: 32
Enviro DRIFTWOOD E30 Installation Manual preview
DRIFTWOOD E30
Бренд: Enviro Страницы: 4
LA NORDICA Crystal 50v Instructions For Installation, Use And Maintenance Manual preview
Crystal 50v
Бренд: LA NORDICA Страницы: 76
CC Products Homesteader Product Manual preview
Homesteader
Бренд: CC Products Страницы: 7
GRAND EFFECTS LIAUT24xxIM Operation And Maintenance Manual preview
LIAUT24xxIM
Бренд: GRAND EFFECTS Страницы: 28
Napoleon SBK4F4B3 Installation Instructions preview
SBK4F4B3
Бренд: Napoleon Страницы: 2
Xaralyn Levico 70 Manual preview
Levico 70
Бренд: Xaralyn Страницы: 10
Continental Fireplaces CB36NTR Installation And Operating Instructions Manual preview
CB36NTR
Бренд: Continental Fireplaces Страницы: 148
Paul Agnew Aerion Series Installation, Operating And Maintenance Manual preview
Aerion Series
Бренд: Paul Agnew Страницы: 104
Woodbridge DVI 750 (N Installation And Operating Instructions Manual preview
DVI 750 (N
Бренд: Woodbridge Страницы: 40
Lopi PEWTER 9850034 User Manual preview
PEWTER 9850034
Бренд: Lopi Страницы: 3
Element4 Direct Vent Gas Fireplace Installation, Operation And Owner'S Manual preview
Direct Vent Gas Fireplace
Бренд: Element4 Страницы: 92
Landmann Patio Lights 23170 Assembly And Use Instructions preview
Patio Lights 23170
Бренд: Landmann Страницы: 4
Napoleon HDX40NT-2 Installation And Operation Manual preview
HDX40NT-2
Бренд: Napoleon Страницы: 112
HEINZE Geniol Instructions For Use preview
Geniol
Бренд: HEINZE Страницы: 2
M Design Luna Diamond 1000CL Instructions For Installation And Use Manual preview
Luna Diamond 1000CL
Бренд: M Design Страницы: 44
Kennedy EF-WM502 Manual preview
EF-WM502
Бренд: Kennedy Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды