Regency City CC40LEPV-LP Скачать руководство пользователя страница 47

Страница: 47 / 88

City Series CC40EPV

| 47

installation

919-696

06.11.18

20 foot Flex pipe Extension

Used in conjunction with the 946-755 Vertical Flex kit for vertical installations

or for horizontal installations when using the power vent option only where a

maximum of 2 946-756 may be used up to a maximum of 40 feet.

Only approved for model # CV72EPV power vent model for any horizontal

terminations.

1. Stretch out both inner 4" (100 mm) and outer 6 7/8" (175mm) pipe up to

a maximum of 20 feet.

Note

:The inner and outer pipes may be cut if only a short length is required.

2. Install spring spacers around 4" (100 mm) inner pipe as shown.

Slide outer flex pipe over and all the way down the 4" pipe.

3. Apply a bead of Mill Pac around the perimeter of the 4" (100mm) inner

collar of the flex adapter and slip the 4" (100mm) inner flex pipe from the

Vertical termination kit over the flex adapter ensuring that the inner flex

pipe overlaps the collar by at least 1-3/8" (35mm). Fasten with 3 screws.

4. Apply a bead of Mill Pac around the perimeter of the 6-7/8" (175mm) outer

collar of the flue adapter and slip it over the 6-7/8" (175 mm) outer flex pipe

from the vertical termination kit ensuring that the outer flex pipe overlaps

the collar by at least 1-3/8" (35mm). Fasten with the 3 screws.

5. Repeat steps to secure the other end of the flex adapter using the flex kit.

6. See Vertical Vent installation instructions or horizontal power vent instal-

lation instructions for installation of the complete vent system.

Note:

If an offset is necessary in the attic or floor joists it is important to sup

port the vent pipe every 3 feet to avoid excessive stress and sagging of the

vent pipe. Wall straps are provided (3 in total) for this purpose.

All round/plumbers strapping may also be used if further supports are

required.

VERTICAL FLUE EXTENSION KIT (APPROVED MODELS)

HORIZONTAL POWER VENT KIT (CV72EPV, CB72EPV, CB40EPV, CV40EPV, & CC40EPV ONLY)

(PART # 946-756)

3 wall straps

flex adaptor

4" (100mm) inner pipe

20ft.

6-7/8" (175mm)

outer flex pipe

20ft

10 spring spacers

Note:

CV72E Power vent model Only - The flex

adaptor which is included with this kit is only

required when joining two of the 946-756

flue extension kits to a maximum of 40 feet.

If only 1 - 946-756 20 foot kit is used the flex

adaptor is not required.

919-698

06.12.18

-1/4

Ceiling ﬁrestop

-1/4

Ceiling ﬁrestop

Diagram 1

Diagram 1a

Enclosure

Ceiling firestop

Flashing

Termination Cap

Storm Collar

Roof support

Ceiling firestop

Enclosure

Ceiling firestop

Flashing

Termination Cap

Storm Collar

Roof support

Ceiling firestop

Firestop spacer to prevent

debris from falling into the ceiling

firestop

A ceiling firestop/firestop spacer must be installed when passing through

each floor or ceiling level. To install the ceiling firestop/firestop spacer in

a flat ceiling or floor joist cut a 10- ¼ inch square hole. Frame the hole as

show in Diagram 1 and install the ceiling firestop. Slide the top attic insula-

tion spacer onto the top of the attic insulation shield/firestop - See Diagram

1a. Secure with 4 screws/nails. If more than one is required, these can be

purchased separately.

Note:

The ceiling firestop/firestop spacer may be cut down to size if this shield

is too high for the application.

CEILING FIRESTOP/FIRESTOP SPACER

( PART # 946-757)

Used in conjunction with the 946-755 Vertical flex kit and 946-756 kit Vertical

flex extension kit/Horizontal power vent kit.

CEILING FIRESTOP/FIRESTOP SPACER

( PART # 946-757)

Used in conjunction with the 946-755 Vertical flex kit and 946-756 kit Vertical

flex extension kit/Horizontal power vent kit.

Firestop spacer to prevent

debris from falling into the ceiling

firestop

A ceiling firestop/firestop spacer must be installed when passing through

each floor or ceiling level. To install the ceiling firestop/firestop spacer in

a flat ceiling or floor joist cut a 10- ¼ inch square hole. Frame the hole as

show in Diagram 1 and install the ceiling firestop. Slide the top attic insula-

tion spacer onto the top of the attic insulation shield/firestop - See Diagram

1a. Secure with 4 screws/nails. If more than one is required, these can be

purchased separately.

Note:

The ceiling firestop/firestop spacer may be cut down to size if this shield

is too high for the application.

Vertical Flue Extension Kit (Part #946-756)

Ceiling Firestop / Firestop Spacer (Part #946-757)

Содержание City CC40LEPV-LP

























































































Результаты поиска

Содержание City CC40LEPV-LP

Отзывы:

Похожие инструкции для City CC40LEPV-LP

Бренды по названию

Популярные бренды

Regency City CC40LEPV-LP, Инструкция для владельца и по установке

Результаты поиска

Содержание City CC40LEPV-LP

Отзывы:

Похожие инструкции для City CC40LEPV-LP

Бренды по названию

Популярные бренды