background image

46

 | 

LRI4E / HRI4E Direct Vent Gas Insert

 | 

46

maintenance

WARNING:  CHILDREN AND ADULTS 
SHOULD BE ALERTED TO THE HAZARDS 
OF HIGH SURFACE TEMPERATURE AND 
SHOULD STAY AWAY TO AVOID BURNS 
OR CLOTHING IGNITION.  YOUNG 
CHILDREN SHOULD BE CAREFULLY 
SUPERVISED WHEN THEY ARE IN THE 
SAME ROOM AS THE APPLIANCE.

MAINTENANCE  
INSTRUCTIONS

1)

  Always turn the gas valve to off before cleaning. 

For relighting, refer to lighting instructions. Keep 
the  burner  and  control  compartment  clean 
by  brushing  and  vacuuming  at  least  once  a 
year. When cleaning the logs, use a clean soft 
paint brush as the logs are fragile and easily 
damaged.

2)

  Clean (never when unit is hot) appliance, door 

and louvers with a damp cloth.  Never use an 
abrasive cleaner. The gold louvers (and optional 
gold door) may be scratched if abrasives are 
used to clean them.

 

The  heater  is  inished  in  a  heat  resistant 
paint and should only be reinished with heat 
resistant paint (not with wall paint). Regency 
uses StoveBrite Paint - Metallic Black #6309.

3)

  Make  a    periodic  check  of  burner  for  proper 

position and condition. Visually check the lame 
of  the  burner  periodically,  making  sure  the 
lames are steady; not lifting or loating. If there 
is a problem, call a qualiied service person. 

4)

  The  appliance  and  venting  system  must  be 

inspected  before  use,  and  at  least  annually, 
by a qualiied ield service person, to ensure 
that the low of combustion and ventilation air 
is not obstructed. 

 

During  the  annual  service  call,  the  burners 
should be removed from the burner tray and 
cleaned. Replace the embers but do not block 
the pilot.

5)

  Keep  the  area  near  the  appliance  clear  and 

free from combustible materials, gasoline and 
other lammable vapours and liquids

6) 

Each  time  the  appliance  is  lit,  it  may  cause 
condensation and fog the glass.  This conden-
sation and fog is normal and will disappear in 
a few minutes as the glass heats up.

 

Never operate the appliance without the 
glass properly secured in place or with the 
door open.

7)

  Do not use this appliance if any part has been 

under water. Immediately call a qualiied ser-
vice technician to inspect the appliance and to 
replace any part of the control system and any 
gas control which has been under water.

8)  

Periodically  check  the  pilot  lames.  Correct 

lame  pattern  has  two  strong  blue  lames:  1 
lowing around the lame sensor, and 1 low-
ing across the burner (it does not have to be 
touching the burner).

.

DOOR GLASS 

Your  Regency    insert  is  supplied  with  high 
temperature,  Neoceram  ceramic  glass  that  will 
withstand the highest heat that your unit will produce. 
If  your  glass  requires  cleaning,  we  recommend 
using  an  approved  glass  cleaner  available  at  all 
authorized dealers. Do not use abrasive materials. 
Do not clean the glass when hot.

In the event that you break your glass by impact, 
purchase  your  replacement  from  an  authorized 
Regency dealer only, and follow our step-by-step 
instructions for replacement.

Door Components

Window Glass

Window Glass Gasket

Door Frame

Window Clip (x4)

Glass Gasket Retainer

Warning: Do not operate 
appliance with glass panels 
removed, cracked or broken. 
Replacement of the glass 
should be done by a licensed or 

qualiied service person.

CAUTION & WARNINGS:

* Do not clean when the glass is hot.
*  The use of substitute glass will void all product
   warranties.
*  Care must be taken to avoid breakage of the
   glass.
* Do not strike or abuse the glass.
* Do not operate this ireplace without the glass
   front or with a cracked or broken glass front.
*  Wear gloves when removing damaged or broken 

glass.

*  Replacement of the glass panel(s) should be
  done by a licensed or qualiied service person.

GLASS REPLACEMENT

In the event that you break your glass by impact,
purchase your replacement from an authorized
Regency® dealer only.
Replacement  Neoceram  glass  (#940-371/P)  is 
shipped with a gasket.

CAUTION:  ANY SAFETY SCREEN OR 
GUARD REMOVED FOR SERVICING AN 
APPLIANCE MUST BE REPLACED PRIOR 
TO OPERATING THE APPLIANCE.

CLOTHING OR OTHER FLAMMABLE MA-
TERIAL SHOULD NOT BE PLACED ON OR 
NEAR THE APPLIANCE.

Glass Door Cleaning & Removal  

Содержание Liberty LRI4E-LP

































































Отзывы: