Regency Fireplace Products Liberty LRI4E-LP, Инструкция для владельца и по установке

Страница: 10 / 64

10 |
LRI4E / HRI4E Direct Vent Gas Insert
|
10
installation
General Safety Information
1) The appliance installation must conform with
local codes or in the absence of local codes,
with CAN/CGA B149 (in Canada) or the National
Fuel Gas Code ANSI Z223.1 in the U.S.A. This
appliance should be installed by a qualiied gas
itter technician only.
2) Installation and repair should be done by a
qualified service person.
3) The appliance should be inspected before use
and at least annually by a professional service
person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding
material, animal hair, etc. It is imperative that
control compartments, burners and circulating
air passageways of the appliance be kept clean.
4) See general construction and assembly
instructions. This appliance may only be
installed in a vented, noncombustible ireplace.
5) This appliance is listed for bedroom installations
when used with a listed Millivolt Thermostat.
Some areas may have further requirements,
check local codes before installation.
6) Always connect this insert to a vent system
venting to the outside of the building envelope.
Never vent to another room or inside a building.
Make sure that the vent is properly sized and is
of adequate height to provide the proper draft.
7) Inspect the venting system annually for blockage
and any signs of deterioration.
8) Any glass removed for servicing must be
replaced prior to operating the appliance.
9) To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the ireplace.
10) This appliance cannot be operated without brick
or enamel panels in place.
11) Due to high temperatures, the appliance should
be located out of high trafic areas and away
from furniture and draperies. Children and
adults should be alerted to the hazards of high
surface temperatures, especially the ireplace
glass and gold trims, and should stay away to
avoid burns or clothing ignition. Young children
should be carefully supervised when they are
in the same room as the appliance. Clothing or
other lammable material should not be placed
on or near the appliance.
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects
or other reproductive harm.
GAS PRESSURE
TESTING
The appliance must be isolated from the gas sup-
ply piping system by closing its individual manual
shut off valve during any pressure testing of the
gas supply piping system at test pressures equal
to or less than 1/2 psig. (3.45 kPa).
INSTALLATION INTO A SOLID FUEL
BURNING FIREPLACE OR FACTORY
BUILT FIREPLACE
The LRI4E / HRI4E Gas Inserts have been tested
and approved to be vented into any masonry ire-
place or approved solid fuel burning factory built
ireplace that will allow the insert to physically it into
the irebox. Refer to "Minimum Fireplace Dimen-
sions" section for minimum ireplace clearances.
If the factory built ireplace* height is too low for
your Insert, you may remove the smoke bafle
plate, damper, refractory (irebricks), glass doors,
screen rails, screen mesh and log grates from the
factory built ireplace as long as these items are
saved and are reinstalled in the event that the Insert
is removed. The ireplace lue damper can be fully
blocked open or removed for installation of the gas
ireplace insert.
Smoke shelves, shields and bafles may be removed
if attached by mechanical fasteners. If any part is
removed it must not weaken the structural integrity
of the factory built ireplace.
The ireplace and ireplace chimney must be clean
and in good working order and constructed of non-
combustible materials.
The surround panels should not seal ventilation
openings on the ireplace.
Chimney clean outs should it properly.
NOTE : Any alterations made to the listed solid fuel
burning factory built ireplace may void the listing
of the ireplace.
Cutting any sheet metal part of the ireplace, in
which the gas ireplace insert is to be installed is
prohibited.
*Check with your local inspector before commencing
with this installation.
Installer must mechanically attach the supplied
label to the inside of the irebox of the ireplace into
which the gas ireplace insert is installed.
" WARNING : This ireplace has been converted
for use with a gas ireplace insert only and cannot
be used for burning wood or solid fuels unless all
original parts have been replaced, and the ireplace
re-approved by the authority having jurisdiction."
FACTORY-BUILT (METAL) WOOD-
BURNING FIREPLACE
REQUIREMENTS
NOTE : Any parts that are removed must be removed
in a way that would allow them to be re-installed if
the insert is ever removed (removal of rivets or
screws is acceptable).
To reference parts—see illustration below.
Must be removed:
1 -Damper
2 - Grate (with log set)
May be removed (if applicable):
3 - Smoke shelf
4 - Internal bafles
5 - Screen
6 & 7 - Masonry lining or refractory
8 - Metal or glass doors
The ireplace must be permanently marked to
indicate that it has been altered and is no longer
suitable for burning solid fuel (wood), unless the
removed parts are re-installed. Cutting of any sheet
metal parts is prohibited.
May be removed (in certain cases):
9 -Metal loor of the irebox
10 - The insulation and any structured rigid frame
members must not be removed or altered (side and
top of door frame, side and top of the face of the
ireplace, metal sides, etc.).
If the factory-built ireplace has no gas access
hole(s) provided, an access hole of 1.5 inch (37.5
mm) or less may be drilled through the lower sides
or bottom of the irebox in a proper workmanship
like manner. This access hole must be plugged
with non-combustible insulation after the gas
supply line has been installed.
CAUTION:
Firebox loor removal is not covered under the
appliance safety standard (ANSI Z21.88, CSA
2.33) used in the safety certiication of this ap-
pliance. The Intertek safety certiication does
not apply to this method of installation. Before
installing the appliance using this method, contact
the Authority Having Jurisdiction to determine
if this installation is acceptable in your area.
The sheet metal base of the ireplace must be
left in place and a minimum 1/2" cement board
sheet placed under the entire length and width
of the appliance.