Regency Fireplace Products Greenfire GF900C Скачать руководство пользователя страница 39

Страница: 39 / 64

Regency GF900C-2 Gas Fireplace

installation

OPTIONAL FAN KIT INSTALLATION

GF950

919-637a

12.14.17

OPTIONAL FAN KIT INSTALLATION

NOTE:

Installation of Fan Kit should be done prior

to installation of the wall.

2. Mount and secure the fan housing assembly to

framing members, the front of the fan housing

will protrude 12.7mm out of the wall so it may be

fi nished with drywall, etc. See diagram 2

3. Install the air duct run. Secure the duct to the duct

collar on the unit and the fan housing with 3 screws

per end and aluminum duct tape.

Diagram 2: Side View - Secure fan housing

to minimum 45mm framing.

Diagram 1:

Front View

Round Air Duct:

Attach the 152.4mm round air duct

(supplied) to the fi replace collar and run the duct to

the fan housing. Attach the round-to-oval adapter

to the fan housing and the air duct to the adapter

45mm

Round to Oval

Adapter

Fan Housing

Secure with 3 Screws and

Aluminum Duct Tape at Unit

Air Duct

7. Screw the Register Adapter Frame and the Air

8. Remove the knock out on the top of the unit.

Cut out the insulation. Remove the second and

third knock out, both are below the top knockout.

9. On the top of the unit, bend the 3 tabs up. Insert

the Duct collar. Secure the collar to the 3 tabs with

screws.

10. Attach fan duct to the unit. Slide the ducting over

the collar and secure with screws.

11. Final step--double check the fan ducting connec-

tions at both the unit and fan. Ensure there is a

minimum of

25mm clearance to combustibles.

Strap and secure the fan duct. Double check

the operation of the fan and all electrical work

is completed.

Diagram 4

Remove the knock out

2nd knockout

cut out insulation

Remove the 2nd knock out

Bend

the tabs

upwards

Third

knockout

Duct collar secured

with screws

4. Install the On/Off switch in a convenient location.

This switch controls the fan operation.

NOTE:

Variable speed or Rotary 3 speed switch

can be fi tted.

5. Wire up the the fan, wall switch and power supply

per local codes. See wiring diagram as reference.

*Electrician to supply wiring.

6. Screw fan junction box to the fan housing.

)LQLVKHG

6XUIDFH

)URQW

RI)DQ

+RXVLQJ

$GMXVWDEOH

%UDFNHWVIRU

GLIIHUHQW

ZDOOIORRU

WKLFNQHVV

Содержание Greenfire GF900C

































































Результаты поиска

Содержание Greenfire GF900C

Отзывы:

Похожие инструкции для Greenfire GF900C

Бренды по названию

Популярные бренды

Regency Fireplace Products Greenfire GF900C, Инструкция для владельца и по установке

Результаты поиска

Содержание Greenfire GF900C

Отзывы:

Похожие инструкции для Greenfire GF900C

Бренды по названию

Популярные бренды