Regency Fireplace Products Greenfire GF900C Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 64

background image

10

Regency GF900C-2 Gas Fireplace

Nailing Strips

(DO NOT REMOVE NAILING STRIPS

WHEN USING COMBUSTIBLE FINISHING)

installation

UNIT ASSEMBLY PRIOR TO INSTALLATION

The nailing strips must be correctly positioned and attached before

unit is slid into position.

NAILING STRIPS-COMBUSTIBLE FINISHING

The nailing strips come attached to the unit. There is 1 plate on each side,
1 on the top.
The top and side nailing strips are secured to the framing.

IMPORTANT NOTE

Framing depth measurement is noted with the nailing strips

set as far forward on the firebox as possible. The nailing

strips can be adjusted back up to 38mm to allow for varying

thicknesses in non-combustible material & wall finishes.

INSTALLATION ACCESS PANEL

The unit is equipped with a removable access panel for pre-finish installation
of optional components - this panel is located on the lower front face.

1. Remove 4 screws to remove access panel.

2. Easier access to gas connection with panel removed.

3. Install any optional components with access panel removed.

4. Reinstall access panel, line up 2 upper tabs and secure in place with

4 screws.

Note: Access panel is no longer usable/accessible once facing material

installed.

Installation Access Panel

Tab locations on access panel

COMBUSTIBLE FINISHING

UNIT ASSEMBLY/ FINISHING/ MANTEL CLEA MANTEL LEG CLEARANCES

«
...
8
9
10
11
12
...
»

Содержание Greenfire GF900C

































































Отзывы:

Нет отзывов

Похожие инструкции для Greenfire GF900C

Бренд: Paloform Страницы: 15

Naples GF301525BK

Бренд: Moda flame Страницы: 7

Бренд: Lennox Страницы: 28

Linear Pebble FRDPU0MN

Бренд: Flavel Страницы: 9

Бренд: EdilKamin Страницы: 16

Бренд: Whalen Страницы: 60

Бренд: Heat & Glo Страницы: 81

Бренд: Blumfeldt Страницы: 124

FP-I-600BK Series

Бренд: Landmann Страницы: 56

Бренд: pleasant hearth Страницы: 12

Бренд: Urbana Страницы: 52

Бренд: EcoSmart Fire Страницы: 40

Бренд: EcoSmart Fire Страницы: 123

Бренд: Horizon Fitness Страницы: 14

Phantasma Tower 10032138

Бренд: oneConcept Страницы: 28

Бренд: Klarstein Страницы: 21

Бренд: Blaze King Страницы: 48

churchill II 347

Бренд: Baxi Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды