Regency Fireplace Products Greenfire GF900C Скачать руководство пользователя страница 36

Страница: 36 / 64

Regency GF900C-2 Gas Fireplace

installation

CONVERSION KIT #466-967 FROM NG TO PROPANE/ULPG
FOR GF900 USING SIT 845 NOVA GAS VALVE

920-039

03/04/19

PRIOR TO CONVERSION, ENSURE UNIT HAS COOLED TO ROOM
TEMPERATURE, ALL POWER IS DISCONNECTED AND GAS SUPPLY
IS TURNED OFF.

1. Remove faceplate, inner frame, glass door, front trim piece and inner

panels- see instructions in this manual.

2. Remove glass crystals and stones, if installed.

3. Remove 3 screws in locations shown below to remove burner tray.

Diagram 1 - Burner Tray Screw Locations

CONVERSION KIT #466-967 FROM NG TO PROPANE/ULPG

FOR GF900 USING SIT 845 NOVA GAS VALVE

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Each Kit contains one Propane / ULPG

Conversion Kit

GF900C Kit# 466-967

Qty.

Part #

Description

904-345

Burner Orifice #53

918-590

Decal “Converted to LP”

919-728

Orange Propane Label

918-272

Conversion to ULPG decal

904-529

5/32” Allen Key

910-037

Propane Injector

911-137

Pilot hood holding clip

919-727

Red ULPG label

920-039

Instruction Sheet

IT WOULD BE BENEFICIAL TO CONVERT THE APPLIANCE PRIOR TO
THE UNIT BEING INSTALLED OR WALL FACING MATERIAL FITTED
WHICH ALLOWS ACCESS TO THE BOTTOM PANEL.

Remove burner orifice with a 12mm spanner and discard. Use
another spanner to hold on to the elbow below the orifice.

Diagram 3 - Remove Pilot Cap

Pilot Cap

Pilot Orifice

Pull off the pilot cap to expose the pilot
orifice (see right).

Unscrew the pilot orifice with the Allen key and replace

with the propane pilot orifice in the kit and replace pilot
cap (see right).

4. Remove burner by removing 2 screws at the back of the burner in

locations shown below.

Diagram 2 - Burner Screw Locations

GF900C-2

Содержание Greenfire GF900C

































































Результаты поиска

Содержание Greenfire GF900C

Отзывы:

Похожие инструкции для Greenfire GF900C

Бренды по названию

Популярные бренды

Regency Fireplace Products Greenfire GF900C, Инструкция для владельца и по установке

Результаты поиска

Содержание Greenfire GF900C

Отзывы:

Похожие инструкции для Greenfire GF900C

Бренды по названию

Популярные бренды