Regency Fireplace Products Grandview G800EH Скачать руководство пользователя страница 19

Страница: 19 / 104

Grandview

G800EH Gas Fireplace |

owner's information

Safety Screen Removal

Slide screen

up.

Slide screen

right.

Lower screen

down.

Swing screen

outwards while

keeping the

screen level

and remove.

To install the safety screen

—Reverse steps above.

Safety Screen Installation

Glass Door Removal

To install the door

—Reverse steps above.

To remove the glass door - place both hands on either side of the

latch. Pull forward then up to unlock, repeat on opposite side.

Important:

After releasing the latches, support the weight of the

door.

2. With both latches released, support the door with both hands and

tilt out to approximately a 60 degree angle.

3. Lift the door up and out of lower slots to remove.

Glass Door Installation

Latch locations

Содержание Grandview G800EH









































































































Результаты поиска

Содержание Grandview G800EH

Отзывы:

Похожие инструкции для Grandview G800EH

Бренды по названию

Популярные бренды

Regency Fireplace Products Grandview G800EH, Инструкция для владельца и по установке

Результаты поиска

Содержание Grandview G800EH

Отзывы:

Похожие инструкции для Grandview G800EH

Бренды по названию

Популярные бренды