Regency Fireplace Products Grandview G800EH Скачать руководство пользователя страница 65

Страница: 65 / 104

Grandview

G800EH Gas Fireplace |

installation

LP Conversion using SIT 885 PROFLAME Gas Valve

G800EH

11.08.22

920-616

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Shut off the gas and electrical supply.

2. Remove the safety screen*.

3. Remove the glass door*.

4. Remove the logs, glass, and any other

media* if already installed.

5. Remove the two log supports* and log

grate assembly by removing 2 screws and

sliding the tray forward to remove.

*(See specific instructions in unit manual.)

Each Kit contains one LP Conversion Kit
Conversion Kit #761-989 Contains:

Qty. Part #

Description

1 904-964

Burner Orifice #51

1 904-529

5/32" Allen Key

1 918-590

Decal "Converted

to LPG"

1 908-528

Red "LP" label

1 910-037

LP Injector (Pilot Orifice)

1 911-011

Stepper Motor

1 761-147

Air Shutter Cap LP

1 920-616

Instruction Sheet

Installation of LP

Conversion Kit:

11. Re-install pilot cap and pilot retainer clip.

12. Remove burner orifice with a 3/8" wrench.

Use another wrench to hold on to the elbow

behind the orifice. Discard orifice.

8. Remove the pilot retainer clip below the

pilot cap.

10. Unscrew the pilot orifice with the Allen

key; then replace with the LPG pilot orifice,

provided in the kit.

Pilot retainer clip

9. Pull off the pilot cap to expose the pilot

orifice.

Diagram 2: Slide burner assembly to

the right—then remove.

Diagram 1: Remove the left and right

screws.

6. Remove three screws then remove the burner

assembly.

13. Reinstall new burner orifice LPG stamped

#51 and tighten.

*Firebox hidden for

clarity*

15. Push the IFC Box back.

LP Conversion Kit (Part #761-989)

G800EH using SIT 885 NOVA Gas Valve

14. Loosen the two Phillips head screws as

shown. They do not need to be removed.

7. Change the air shutter cap. Remove the cap by

removing one screw as shown. When installing

LP air shutter cap, do not fully tighten the

screw so that the cap can be freely rotated.

Left – NG cap. Right – LP cap

Содержание Grandview G800EH









































































































Результаты поиска

Содержание Grandview G800EH

Отзывы:

Похожие инструкции для Grandview G800EH

Бренды по названию

Популярные бренды

Regency Fireplace Products Grandview G800EH, Инструкция для владельца и по установке

Результаты поиска

Содержание Grandview G800EH

Отзывы:

Похожие инструкции для Grandview G800EH

Бренды по названию

Популярные бренды