Regal 3200 Bowrider Скачать руководство пользователя | Manualshive

Страница: 96 / 316

background image

CHAPTER 4

4-12

Fuel Vents

Currently, domestic EPA compliant fuel tanks vent fumes back into the
fuel tank system. While the tank is

fi

lled, air displaced by the incoming

fuel is vented through the fuel system charcoal canister.

Your vessel uses a combo type
(internal vented) fuel

fi

ll. Both the

fuel

fi

ll and vent occupy the same

cavity under a protective cover. If
fuel over

fl

ows through the vent the

design forces it back into the fuel

fi

ll

hose and tank.
A seasoned skipper will hear a
distinct sound as the tank nears the

“top out” or full mode and may see fuel over

fl

owing back into the fuel

hose through the vent. DO NOT OVERFILL THE TANK. This helps
avoid any overboard spills which harm the environment. There is a key
that

fi

ts the fuel

fi

ll. Use it to secure the

fi

tting from leaking fuel. Store

the key in a safe place so it can be easily found for fueling. Check the
vent

fi

ll screen periodically for debris.

COMBO FUEL FILL W/
INTERNAL VENT

The fuel tank feed lines each use an anti-siphon valve. The valve is
threaded into each fuel tank

fi

tting at the feed line. The valve is pulled

off its seat by fuel pump pressure as the engine is cranking or running.
It allows a one-way fuel roadway to the engine fuel pump . It prevents
fuel from siphoning out of the tank in the event of a fuel line rupture
or disconnected fuel feed hose. See the fuel tank maintenance chapter
or technical section for more speci

fi

c information on the anti-siphon

valve location. Never remove an anti-siphon valve as it is a fuel system
safety component.

Anti-Siphon Valve

«
...
94
95
96
97
98
...
»

Содержание 3200 Bowrider





























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3200 Bowrider

Бренд: MACGREGOR Страницы: 24

Бренд: Vanguard Sailboats Страницы: 8

Бренд: Fish Cat Страницы: 6

Бренд: Sea-doo Страницы: 14

Бренд: Sea-doo Страницы: 88

Бренд: Grady-White Boats Страницы: 78

Бренд: Grady-White Boats Страницы: 82

Бренд: Grady-White Страницы: 112

Бренд: Candela Страницы: 55

Бренд: Malibu Boats Страницы: 164

2014 Waverunner FX Cruiser HO

Бренд: Yamaha Страницы: 124

2005 SuperJet 700

Бренд: Yamaha Страницы: 114

Бренд: TOPCAT Страницы: 72

Бренд: Silverline Страницы: 18

Mini Camper Cruiser

Бренд: Portable Boat Plans Страницы: 5

Бренд: Jones Brothers Страницы: 64

Бренд: ANYTEC Страницы: 9

Бренд: ANYTEC Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды