Regal 3200 Bowrider Скачать руководство пользователя

Страница: 175 / 316

Equipment Operation

6-43

Typical Gas Grill-Operating Instructions

•

A universal mount is required to attach the grill to the deck

tting.

• Fit the grill-mount assembly to the grill and into the deck

tting. Make

sure the grill is positioned securely.

• Screw on the propane bottle.

• With a long match or propane starter apply

ame to the burner. Always

apply the

ame to the burner before turning on the gas.

• The control knob now can be turned to start the grill.

WARNING

GASOLINE VAPORS ARE EXPLOSIVE!

OPEN FLAME APPLIANCES CAN IGNITE GASOLINE VAPORS.

TO AVOID INJURY OR DEATH FROM EXPLOSION OR FIRE,

TURN OFF ALL OPEN FLAME DEVICES.

Содержание 3200 Bowrider





























































































































































































































































































































Результаты поиска

Содержание 3200 Bowrider

Отзывы:

Похожие инструкции для 3200 Bowrider

Бренды по названию

Популярные бренды

Regal 3200 Bowrider, Руководство пользователя

Результаты поиска

Содержание 3200 Bowrider

Отзывы:

Похожие инструкции для 3200 Bowrider

Бренды по названию

Популярные бренды