manualshive.com logo in svg

Regal 3200 Bowrider, Руководство пользователя

Поделиться
Скачать
Regal 3200 Bowrider Скачать руководство пользователя страница 164

CHAPTER 6

6-32

Keel Offset. 

By pressing the “ON/OFF MODE” keypad again displays 

the “KL” keel offset setting. It can be set so the depth 

fi

 nder shows 

the depth below the transducer or the depth under the keel. Press the 
“UP” or “DOWN” arrow keypads to adjust the reading to the desired 
depth no further than 19.9 feet. 
An example would be if  the keel bottom is 3 feet below the transducer 
and you desire the depth sounder to read the depth below the keel, the 
display should be adjusted to read 3.0 FT.

Note: 

Once the keel offset is programmed, the shallow and deep alarms 

will be energized by the depth under the keel. 

Units. 

Pressing the “ON/OFF MODE” keypad again displays “UN” 

on the LCD indicating the units mode.
Press either the up or down arrow keypads to set the units desired to 
(FT) feet, (M) meters, or (F) fathoms. Once these units are set, they will 
remain the same for all modes. By pressing the “ON/OFF MODE” 
keypad again returns the depth 

fi

 nder to normal operation.

Note: Near the keel (center 
of  boat bottom)the depth 
sounder transducer is lo-
cated. It bounces a constant 
signal off  the bottom and 
sends it to the dash head 
unit. Never use bottom 
paint on the hull side of  
the transducer since it will 
effect the unit’s operation.

Typical 

Transducer

Содержание 3200 Bowrider





























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды