Regada MP 52 200 Скачать руководство пользователя страница 13

MP 52 200

 

 

11 

After  receiving  of  the  EA  check  whether  during  their  transport  or  storing  no  damage 

occurred.  Compare  the  data  on  their  nameplates  with  the  accompanying  documentation/the 
purchase  agreement  (the  order).  In  case  of  any  discrepancy,  failure  or  damage  inform  about 
the fact the producer immediately. 

 

 

If not installed immediately the EA and their equipment should be stored in dry, well-conditioned 

sheltered areas, protected against impurities, dust and soil humidity (with keeping them on shelves or 
pallets),  chemical  and  unauthorized  impacts,  at  ambient  temperature  from  -10°C  to +50

°

C  and  at 

relative air humidity max. 80 %.  

 

a)  It is forbidden to store EA outside or in areas not prevented against direct impact of climate. 
b)  Strains  of  the  surface  finishing  should  be  promptly  removed  if  any  –  it  can  prevent the product 

against corrosion damages. 

c)  While storing more than one year it is necessary to check lubrication filling before the actuator is 

put into operation. 

d)  The EA installed but not operated are to be protected the same way as when storing (e.g. with a wrapping). 
e)  After  it  is  mounted  onto  a  valve  in  free  and  wet  areas  or  in  areas  where  temperature  is  changing  it  is 

necessary  to  connect  the  space  heater  –  to  prevent  the  actuator  against  corrosion  resulted  from  water 
condensed in the control part. 

f)  Remove odd conservation grease as late as before putting into operation.  

 

1.9  Liquidation of the Product and the Package 

The product is made of recyclable. The single parts of the package and the product should not 

be  thrown  away  after  its  lifetime  but  sorted  according  to  the  related  regulations  and  rules  about 
environment protection and delivered for next treatment. 

  The product itself as well as its package is not a source of spoiling of environment and they do 

not contain any dangerous waste. 
 
 

2.  Installation and Dismantling of the Actuator 

 
Follow safety regulations

 

Note:  
 

Check again whether the EA is place in accordance with the Chapter “Operation Conditions”. If the 

installation  conditions  are  different  than  recommended  it  is  needed  to  consult  the  situation  with  the 
producer. 

Before starting the installation onto the valve: 

· 

Check again whether the EA was not damaged while storing. 

· 

Check compliance of the stroke adjusted by the producer and the connecting dimensions of the EA 
with the parameters of the valve. 

· 

In case of any difference perform the adjustment according to the Chapter “Adjustment”. 

 

2.1.1  Mechanical connection 

 

EA  is  by  the  producer  adjusted  to  parameters  according  to  the  nameplate,  with  connecting 

dimensions according to the corresponding dimensional drawing and put it to a mid-position. 
 

Before installation put the handwheel on. 

 

Mechanical lever-joint connection 

· 

Properly defat contact surfaces of the EA, connecting flange and the valve/gearing. 

· 

Coat the valve/gearing output shaft firmly with a grease not containing any acid. 

· 

Reset the EA to the limit position "closed"; put the valve to the same limit position. 

· 

Put the EA onto the valve to have the output shaft reliably in the valve/gearing coupling. 

· 

Use the handwheel to turn the EA if needed to reach compliance between holes in the EA flange 

and the valve. 

!

Содержание MP 52 200























Отзывы: