background image

www.reechcraft.com/PowerMast   

888-600-6160

47

secti
On 

6

TRANSPORT, STORAGE, AND MAINTENANCE

 DAILY INSPECTION AND MAINTENANCE LOG (2 OF 2)

Component 

OK Inspection/Action

Gearbox

Inspect input shaft for wear or damage. If hex is rounded or 
damaged in any way, replace immediately.

Lock Lever

Inspect the lock lever for any damage or excessive wear. 
Ensure torsion spring returns the lock lever to rest position 
freely and quickly. Inspect to make sure that bolts are tight and 
securing the lock lever assembly to the climbing unit. While 
raising the climbing unit, listen for audible ratcheting pattern. 
Pattern should be uniform both in volume and frequency.

Overspeed Brake

Ensure the overspeed brake is securely fastened to the 
climbing unit with the bolts

Drill Bracket

Inspect the drill bracket for any damage or misshapen parts. 
Check that bolts are securely fastening the drill bracket to the 
climbing unit. Fasten the drill to the gearbox using the drill 
bracket. Be sure the drill assembly with nut driver freely moves 
on to hex input shaft of the gearbox and engages fully. Secure 
the drill to the drill bracket by tightening the wing nut.

Platform Support

Inspect all platform support for any loose connections or 
damaged components. Ensure the support is connected 
securely to the climbing unit, inspecting the bolt connections 
and locking pins that secure them to the climbing unit. Be sure 
all hardware used for adjustment is present and functioning 
properly.

Masts

Inspect mast for damage and straightness. Discard and replace 
as necessary. Check for any missing screws on the track and 
replace. Be sure all hardware is present, secure, and fastens 
properly. Inspect the top stop of the mast to ensure it functions 
properly.

Ties

Inspect the entire tie for any loose connections, misshapen, 
broken or damaged parts. Discard and replace parts as neces-
sary.

Work Platform

Inspect that guardrails are in place and functioning properly. 

Drills

Check cords and nut driver. Be sure that nut driver is securely 
fastened. Discard or repair any damaged electrical cords.

Cords, Powerboards

Check for any damage. Discard or repair immediately.

Содержание PowerMast Series





















































Отзывы: