background image

 

2 – Parallel processing (FX1 – FX2 – FX3) 
 
These are the three main parallel processors. Everything is coming from the return jacks of L3 (mono 
or stereo) will be split into three mono or stereo sends, in order to feed FX1/2/3 inputs plus a dedicated 
fourth pat, for the dry signal (this last one is internal).  
These three processors are connected in parallel, one to each other. 
The returns of these four audio paths (three processors plus the dry path) will be directly summed to 
the output stage.  
 
How to wire (FX1 – FX2 – FX3)?  
No more special cable needed, from this point on, you can use standard 

¼

’ or 6.3mm MONO jack. Each 

device has the ability the be connected in full stereo mode (stereo input/stereo output) into the mixer.   
 
Let’s dig a bit deeper. Scenarios at this point can be quite a few.  
 

1 – All three serial loops are mono (L1 – L2 – L3), but my first parallel processor has stereo input (FX1). 
How do I split a mono signal into a stereo one?  

MSLM will do it for you. You only just need to connect both of FX1 send jacks to the input jacks of your 
device, MSLM will send an exact copy to both inputs of what is coming from the mono output of L3.  
 

2 – First two serial loops are mono (L1 – L2) but third loop is stereo (L3), my first parallel processor 
has stereo input (FX1). How do I connect my parallel processors?  

Self-answering question. The devices putted in L3 will split the signal for you, you only just need to 
connect both of FX send jacks to the input jacks of your device. 
This is configuration can be also applied if two or all three loops (L1 – L2 – L3) are wired in stereo.  
 

3 – One or more of the serial loop (L1 – L2 – L3) or at least the last one (L3) are stereo, but my first 
parallel processor FX1 has mono input, how do I need to connect it?  

There’re two possible ways to do it.  If you are ok to send only one side of L3 to the the mono input of 
FX1, you can use the left side, with a simple mono cable.  
If you want to send the entire stereo signal, collapsing what is coming out of L3 into a mono send, you 
need to create a special Y cable, with three mono jacks. Two jack will be placed into FX1 sends, the 
third one with both cables soldered together, will be insert into your processors’ input jack.  

NOTE: by collapsing both FX1 sends into a mono signal, will NOT affect FX2 and FX3 sends. You will 

maintain the stereo image intact. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание MSLM
















Отзывы: