12
3. To save temperature, do not press any button for 5 seconds.
Note! The device automatically disables the KEEP WARM function if
operating temperature of the program is below 170°F (75°С). Previous
temperature settings are disregarded.
To Adjust the Time:
1. Press TEMP twice while the program is in progress. The time value start
to blink.
2. Use “+” to increase the time value in 1 hour increments. Use “–“ to
increase the time value in 1 minute increments. Hour and minute
value increase irrespectively from each other. After maximum value
is reached the adjustment starts from the minimum value. Press and
hold the corresponding button down to scroll through the digits.
3. To save time, do not press any button for 5 seconds.
If you set the cook time of “00:00”, the program stops its operation.
Do not enter more than 1 adjustment within a minute, because the
appliance will only save the last adjustment made. If the recipe
requires to change both the time and temperature press the TEMP
button after entering time or temperature adjustment. The appliance
will save both adjustments as one.
Save the Adjusted Program
Within 3 minutes after the cycle is complete you can save the adjusted
program to the memory of the appliance, replacing the initial program with
the new one. Display shows 3-minute count down in 1 second increments.
To save the program press the TIME DELAY button before the countdown
is completed. To exit without saving press CANCEL/REHEAT.
To Run a Saved Program
1. Use the MENU and “+”, “–” buttons to select the program that was previ-
ously adjusted and saved. Instead of the default time, the display shows
the “----” sign.
2. Press START/KEEP WARM. During the cycle, a short audible signal is
produced to indicate of each time and temperature adjustment. If
time or temperature of recalled program were adjusted once again,
the appliance will offer to save a new program to the memory after
the cooking cycle is completed.
Saved programs can be adjusted in the same manner as automatic.
However, new adjustments made to the program cancel all other
adjustments that were supposed to follow.
To Restore to Factory Settings
The appliance enables to reset one adjusted program or all of them back to
their default settings. Select the adjusted program and press ОK. To confirm
resetting press and hold down the MENU button. The program will be reset
to default settings.
Deleted program will be replaced by the initial automatic cooking
program.
To restore all programs back to factory settings, press and hold down the
MENU button for 3–4 seconds in standby mode.
Standard Operating Procedure for Automatic Programs
1. Measure the ingredients according to the recipe and place them into
the removable bowl. Make sure that all ingredients are below the max-
imum fill mark on the inside of the bowl..
2. Position the bowl inside the appliance. The bowl must make full
contact with the heating element. Close the lid until it clicks into
place. Plug in the appliance.
3. Press the MENU button to select a program. Use “+” and “–” to navigate
through the menu. The START/KEEP WARM, OK, and “+”, “–” button
indicators, and the Selected program indicator start to blink. If the
TIME DELAY function is applicable for the selected program then the
TIME DELAY button indicator lights.
4.
Press the ОК button and set cook time of the program.
5. Delay the program if necessary.
6. Press and hold down the START/KEEP WARM button. The cycle begins.
The START/KEEP WARM and CANCEL/REHEAT button indicators light
up. The countdown starts and the Cooking progress indicator is displayed.
7. After the cycle is complete an audible sound is heard. Depending on
your settings the device either enters KEEP WARM (the CANCEL/
Содержание RMC-250A
Страница 2: ...1 2 3 4 5 7 8 12 9 10 6 11 14 15 16 13 17 A1...
Страница 3: ...MENU MASTERCHIEF SAVE RESET TIME DELAY KEEP WARM CANCEL REHEAT OK START TEMP 1 2 4 3 5 6 7 8 9 A2...
Страница 5: ...ENG 6 FRA CAN 23 ESP 43...
Страница 63: ...63 RMC 250A ESP...