background image

 

 

 

 

 

SAFETY INSTRUCTIONS

 

 

1. 

Never disconnect or shortcut any of the safety switches.     

2. 

The VERTI-DRAIN can be used as a sit-on and walk-in front unit. We strongly 
advise to transport the machine whilst sitting on the unit (gear 4,5 or 6) and to walk 
in front when working (gear 1,2 and 3) with the VERTI-DRAIN. 

3. 

 The VERTI-DRAIN is suited exclusively to grass fields

4. 

 Every VERTI-DRAIN user must be fully informed of the information contained in 
the user manual. 

5. 

 Inspect the ground where the VERTI-DRAIN is to be applied. Remove loose 
obstacles, avoid uneven ground. 

6. 

 Never step off the unit if the engine is still running. 

7. 

 Ensure that other people are standing at least 4 mtr. (14' ) away from the VERTI-
DRAIN. 

8. 

 Use appropriate clothing. Wear strong shoes with a steel inforced toe cap, long 
trousers, tie up long hair. Do not have any loose pieces of clothing. 

9. 

 Never try to force the VERTI-DRAIN, a situation which is visible in the partial 
loosening of the front roller from the ground and unstable behavior of the VERTI-
DRAIN. 

10. 

Check the VERTI-DRAIN once a week to ensure there are no loose screws or nuts 
and bolts. 

11. 

 The VERTI-DRAIN may never be used without protection covers and safety 
stickers. 

12.

 

NEVER crawl underneath the VERTI-DRAIN.  

13.

 

 Always switch off the engine, before starting any maintenance, adjustment or repair. 
Also block the VERTI-DRAIN against sinking and block it against forward/backward 
movement or sliding. 

14. 

 Use only the original VERTI-DRAIN spare parts/ tines in order to ensure the safe 
operation of the machine. 

15. 

 Never use the VERTI-DRAIN in the dark, in heavy rain, on frozen ground,  stormy 
conditions or on slopes greater than 20 degrees. 

16. 

 Before operating the machine, also read the instructions and the maintenance 
information for the Honda engine
. This component has its own certification mark. 

17. 

 Maintain a log book of repairs

18.

 

If any modifications are carried out on the machine the CE certification mark will 
be no longer valid
. The User/Dealer himself must then have the machine re-certified. 

19.

 

The unit can not be used on public roads 

20.

 

Wear certified ear protection, against the noise 

 

 

 

 

 

Содержание Verti-Drain 7007































Отзывы: