manualshive.com logo in svg

Redexim Turf-Stripper 1200, Руководство пользователя и каталог запчастей, Страница: 18 / 26

Поделиться
Скачать
Redexim Turf-Stripper 1200 Скачать руководство пользователя страница 18

 

18 

 

13. 

TROUBLE SHOOTING (PROBLEM ANALYSIS) 

 

Problem 

Possible cause 

Solution 

 

Machine vibrates. 

-

  Obstacle(s) between the 

knives 

-

  Worn or broken knives. 

-

  Rotor is off-balance. 

-

  Remove the obstacle(s). 

 

-

  Replace with new knives. 

-

  Balance the rotor. 

 

Working depth is not 
achieved. 

-

  Working depth is not adjusted 

correctly. 

 

-

  Subsoil is too hard. 

 
 
 

-

  Driving speed is too high. 

 

-

  Adjust the working depth 

properly. 

 

-

  Lower the driving speed or 

pass over the soil more than 
once. 

 

-

  Lower the driving speed. 

 

Too coarse processing 
of the soil 
 

-

  Driving speed is too high. 

 

-

  Subsoil is too wet. 

 

-

  Decrease the driving speed. 

 

-

  Wait for better conditions. 

 

Rotor is jammed. 

-

  Subsoil is too wet. 

 

-

  Obstacle(s) between the 

knives 

 

-

  Driving speed is too high. 

 

-

  Too much overgrowth 

 

-

  Wait for better conditions. 

 

-

  Remove the obstacle(s). 

 
 

-

  Decrease the driving speed. 

 

-

  Cut the overgrowth. 

 

Rotor does not turn. 

-

  The V-belts that drive the rotor 

slip. 

 

-

  Machine is adjusted too deep. 

-

  Pull the V-belts taut. 

 
 

-

  Adjust the machine to less 

depth. 

 

Transport belt cannot 
cope with the quantity 
of material. 

-

  Driving speed is too high. 

 

-

  Transport belt turns too slowly. 

 

-

  Lower the driving speed. 

 

-

  Increase the oil flow of the 

tractor. 

 

Transport belt moves 
slowly or does not move 

-

  No hydraulic flow 

 

-

  Transport belt slips 

 

-

  Check hydraulic connections 

 

-

  Tighten the transport belt 

 

Содержание Turf-Stripper 1200



























Отзывы:

Нет отзывов