Redexim Turf-Stripper 1200 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 26

Redexim Turf-Stripper 1200 Скачать руководство пользователя страница 10

10

3. FIRST INSTALLATION

– TAKING THE MACHINE OFF THE

PALLET

The machine is placed vertically on the pallet. To remove the pallet and to place the machine
horizontally on the ground, take the following steps

(see Figure 8)

:

!! NEVER CRAWL UNDER THE MACHINE !!

1. Attach a cable to the lifting eyes on both sides of the machine.

Make sure that the cable/crane/lift can hoist minimum twice the weight of
the machine.

(See Chapter 1.0 ‘Technical Data’ for the weight details.)

2.

Lift the machine including the pallet of approx. 50 mm (2”) off the ground.

3. Remove the pallet by removing the three-point pins A.

!! NEVER crawl under the machine !!

4. Slowly lower the machine until it touches the ground.

!! Attention: the machine can swing dangerously !!

5. Attach the machine to a tractor. (See Chapter 4.0 for instructions abolt

attaching to the tractor.)

Use the proper tractor (please refer to the specifications).

Turn off the tractor and secure the tractor / Turf-Stripper combination
against driving off and/or sliding off.

Figure 8

«
...
8
9
10
11
12
...
»

Содержание Turf-Stripper 1200



























Отзывы:

Нет отзывов