REDEX MSR 330 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 40

REDEX MSR 330 Скачать руководство пользователя страница 3

2 SPEED GEARBOX

User manual

Ref.: RX142/046

Version 09/05/2017 - English

This document must not be reproduced nor information therein disclosed without our authorization

Page 3 / 35

1 INTRODUCTION

The MSR 2 speeds spindle gearbox will give you complete satisfaction if all of the following
mounting, operating and maintenance instructions are respected.
This gearbox is delivered:



Fully tested (leakage, speed change motoreducer, noise level, vibration, temperature)



Ready to be mounted

1.1 Warnings

1.2 Gearbox identification

Each unit can be identified through its identification plate and the serial number indicated on it. The
serial number must be given for any correspondence on a particular unit.

1.3 Long term storage

Each gearbox is delivered wrapped and greased for 1 month anti-corrosion protection. Gearboxes
which are not installed shortly after receipt should be stored in a dry atmosphere with temperature
between 0°C & 40°C. The unit must be filled completely with oil for storage.

WARNING! LUBRICATION REQUIREMENTS.

The MSR is delivered WITHOUT OIL: refer to lubrication chapter in this
manual to respect all lubrication requirements.
any damage due to incorrect lubrication will void the warranty.

Serial number

Drawing code

Designation

Shipment date

Reduction ratio

Backlash (if

needed)

861900

RX132605-00

MSR334

NOV. 2016

2.00/7.66

«
1
2
3
4
5
...
»

Содержание MSR 330









































Отзывы:

Нет отзывов