REDEX MSR 330 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 40

background image

2 SPEED GEARBOX

User manual

Ref.: RX142/046

Version 09/05/2017 - English

This document must not be reproduced nor information therein disclosed without our authorization

Page 29 / 35

6.2 Ratio change by pneumatic / hydraulic actuator (2 positions)

Ratio change is done by reversing the supply circuit. The pneumatic or hydraulic actuator

interface is 1/8” GAZ. Operating pressure range is from 5 to 10 bars.

Power supply for ratio 1/1

Power supply for reduction

Proximity sensors MSDbvr35 & MSDbvr 60

Proximity sensors MSDbvr 12

6.3 Ratio change by pneumatic / hydraulic actuator (3 positions)

Specific 3 positions ratio change actuators are able to include

a neutral position,

please ask

your nearest REDEX agent for specific instructions.

WARNING!

The gear shift actuator pressure has to be maintained while running the
MSD gearbox to insure that the gear remains engaged.

«
...
27
28
29
30
31
...
»

Содержание MSR 330









































Отзывы:

Нет отзывов

Похожие инструкции для MSR 330

Бренд: Lenze Страницы: 72

Бренд: Inovance Страницы: 42

Бренд: LaCie Страницы: 32

VLT BACnet/IP MCA 125

Бренд: Danfoss Страницы: 18

Бренд: K&R Страницы: 362

Бренд: Masterflex Страницы: 20

FRENIC HVAC Series

Бренд: FujiFilm Страницы: 20

Бренд: Penta KB Power Страницы: 24

Бренд: Kieback&Peter Страницы: 10

Бренд: Bodine Страницы: 6

Бренд: Bodine Страницы: 44

Бренд: Leadshine Страницы: 18

Servo Motor Kit

Бренд: Terasic Страницы: 20

Reliance Electric MD65

Бренд: Rockwell Automation Страницы: 188

Zip 250MB Parallel Port Drive

Бренд: Iomega Страницы: 24

Бренд: Iomega Страницы: 16

SGD7S-****20A Series

Бренд: YASKAWA Страницы: 561

Бренд: Eurotherm Drives Страницы: 203

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды