Redarc MANAGER 30 Скачать руководство пользователя

Страница: 32 / 40

USER GUIDE

Faults

CHARGER FAULT MESSAGE

CAUSE

ACTION

Charger over current fault

An internal error has caused excessive

current draw

Return to supplier

Charger over voltage fault

The output voltage is too high (above

18V)

Check battery is correct type (12V, 6

cell)

Charger over temperature. Allow to cool

The unit has over heated

Allow to cool, charging will

recommence automatically

Output battery under temperature

Output battery is below 0°C

Charger will halt charging until battery

is above 5°C

Output battery over temperature

Output battery is above 60°C

Charger will halt charging until battery

is below 55°C

Dry cell detected in output battery

Charger has detected a dry cell in

output battery

Replace battery

Shorted cell detected in output battery

Charger has detected a shorted cell in

output battery

Replace battery

Warnings

CHARGER WARNING MESSAGE

CAUSE

ACTION

AC supply over voltage

The internal AC converter output

voltage is too high

Contact supplier

AC supply over temperature. Allow to cool

The internal AC converter temperature

is too high

Contact supplier

DC supply over voltage

The DC input voltage is too high (over

32V)

Check DC input, refer to specified input

range

Solar supply over voltage

The solar input voltage is too high

(above 32V)

Check solar input, refer to specified

input range

No battery sensor connected

The supplied battery sensor is not

connected or is faulty

Connect battery sensor, if faulty return

to supplier

Battery SoC low! Disconnect all loads

House battery is almost flat

Reduce/remove loads on house battery

Battery voltage low! Disconnect all loads

Loads exceeding charge available from

input sources

Connect additional input source or

disconnect loads

Bad cable detected

Too much voltage drop between

charger and battery sensor

Check cable for correct sizing

requirements

Load Disconnect output shorted

Load disconnect output faulty

Contact supplier

Other issues

FAULT

ACTION

Low output current can occur when the unit is hot and

temperature derating is implemented to protect the Charger

Check that the unit is in a well ventilated space

The current display shows a negative current when there

are no loads on the house battery and the house battery is

charging

The current shunt connection is reversed

Noticable oscillations between Boost and Absorption stages

Check and select the correct battery type

Содержание MANAGER 30









































Результаты поиска

Содержание MANAGER 30

Отзывы:

Похожие инструкции для MANAGER 30

Бренды по названию

Популярные бренды

Redarc MANAGER 30, Руководство пользователя

Результаты поиска

Содержание MANAGER 30

Отзывы:

Похожие инструкции для MANAGER 30

Бренды по названию

Популярные бренды