Red Jacket 344-001-5 Скачать руководство пользователя страница 4

1

  Introduction

This manual contains installation, operation, and service information for the Red Jacket 4-inch Standard 
Submersible Petroleum and AG pump.

Safety Precautions

The following safety symbols are used throughout this manual to alert you to important safety hazards and 
precautions.

EXPLOSIVE

Fuels and their vapors are extremely 
explosive if ignited.

FLAMMABLE

Fuels and their vapors are extremely 
flammable.

ELECTRICITY

High voltage exists in, and is supplied 
to, the device. A potential shock haz-
ard exists.

TURN POWER OFF

Live power to a device creates a 
potential shock hazard. Turn Off 
power to the device and associated 
accessories when servicing the unit.

WARNING

Heed the adjacent instructions to 
avoid equipment damage or personal 
injury.

READ ALL RELATED MANUALS

Knowledge of all related procedures 
before you begin work is important. 
Read and understand all manuals 
thoroughly. If you do not understand 
a procedure, ask someone who does.

WEAR EYE PROTECTION

Wear eye protection when working 
with pressurized fuel lines or epoxy 
sealant to avoid possible eye injury.

WARNING

This product operates in the highly combustible atmosphere of a gasoline storage tank.

FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS AND SAFETY PRECAUTIONS 
COULD CAUSE DAMAGE TO PROPERTY, ENVIRONMENT, RESULTING IN SERIOUS INJURY 
OR DEATH.

1. All installation work must comply with the latest issue of the National Electrical Code 

(NFPA 70), Code for Motor Fuel Dispensing Facilities and Repair Garages (NFPA) 30A, 
and any national, state, and local code requirements that apply.

2. Turn off, tag, and lockout power to the STP before connecting or servicing the STP.

3. Before installing pipe threads apply an adequate amount of fresh, UL classified for 

petroleum, non-setting thread sealant.

4. To protect yourself and others from serious injury, death, or substantial property 

damage, carefully read and follow all warnings and instructions in this manual. 

5. When servicing unit use non-sparking tools and use caution when removing or 

installing equipment to avoid generating a spark.

OFF

OFF

Содержание 344-001-5
















Отзывы: