Red Epic REDCAST Скачать руководство пользователя страница 12

Страница: 12 / 35

REDCAST MODulE OPERATION GuIDE

955-0072, REV-H | 12

OUTPUT QUAD UHD OR 1080P

With the REDCAST Module, you can output the following:

“Output Quad UHD” on page 12

“Set Up 1080p” on page 14

OUTPUT QUAD UHD

This section explains how to output 4K Ultra-High Definition (UHD) via the REDCAST Module.

REQUIRED ITEMS

DSMC

BRAIN

Adaptor module (either a +1 Adaptor Module or a Module Adaptor)

REDCAST Module

Four (4) 3G/HD-SDI cables

Quad 3G/HD-SDI device

SET UP QUAD UHD 3G/HD-SDI

1. Turn the BRAIN off.
2. Install the REDCAST Module on the BRAIN. For more information, go to

“Install the REDCAST Module” on

page 10

3. Use four (4) 3G/HD-SDI cables to connect the four (4)

SDI-OUT

ports on the REDCAST Module to the four

(4)

3G/HD-SDI IN

ports on a quad 3G/HD-SDI device.

NOTE:

Be careful to connect each cable from the REDCAST Module to the appropriate connector on the

device. For example, connect SDI-OUT 1 on the REDCAST Module (top left quadrant) to 3G/HD-SDI IN

1 on the device.

4. Turn on the BRAIN.
5. Go to

Menu

Settings

Project

Format

UHD

The UHD menu lists the formats that are capable of displaying on a 4K display.

6. Select the

Resolution

and

Aspect Ratio

. Options depend on the camera type:

‒

EPIC DRAGON

: 6K 16:9 (HD); 5K 16:9 (HD); 4K 16:9 (HD)

‒

SCARLET DRAGON

: 5K 16:9 (HD); 4K 16:9 (HD)

NOTE:

The REDCAST Module scales down to the output resolution you select in

Step 9

. However, the

resolution you select in this step is recorded to the SSD.

Содержание REDCAST




































Результаты поиска

Содержание REDCAST

Отзывы:

Похожие инструкции для REDCAST

Бренды по названию

Популярные бренды

Red Epic REDCAST, Руководство по эксплуатации

Результаты поиска

Содержание REDCAST

Отзывы:

Похожие инструкции для REDCAST

Бренды по названию

Популярные бренды