DC
Setting
Values
Description
Pre-flow
0-20s
Set how long you would like your gas to flow before the arc ignites.
Start Amp
10-200A
Set the starting current when the arc ignites.
Up Slope
0-20s
Set how long it takes for the Start Amp to reach the Peak Amp.
Peak Amp
10-200A
Set the peak welding current.
Down Slope
0-20s
Set how long it takes for the Peak Amp to reach the End Amp.
End Amp
10-200A
Set the End Amp to adjust how hot your weld will finish.
Post Flow
0-20s
Set how long you would like your gas to flow after the arc ends.
SpotPlus™
0-60s
SpotPlus improves the spot welding mode by applying an adjustable synergic pulsed program. The program
speeds up the spot tacking process and is perfect for sheet metal fitups with gaps.
ArcPlus™
0-50A
ArcPlus keeps the volt amps constant by adjusting the welding current proportionally as the arc voltage
increases or decreases during a weld. It helps give better puddle control when weaving, reduced heat input
and increased side wall fusion.
TackPlus™
0-6Hz
TackPlus allows you to preset a tacking procedure to reduce the time required for tack welding, and also
reduces the heat input in the joint between tacks, improving the quality.
AC
Setting
Values
Description
Pre-flow
0-20s
Set how long you would like your gas to flow before the arc ignites.
Start Amp
10-200A
Set the starting current when the arc ignites.
Up Slope
0-20s
Set how long it takes for the Start Amp to reach the Peak Amp.
Peak Amp
10-200A
Set the peak welding current.
Down Slope
0-20s
Set how long it takes for the Peak Amp to reach the End Amp.
End Amp
10-200A
Set the End Amp to adjust how hot your weld will finish.
Post Flow
0-20s
Set how long you would like your gas to flow after the arc ends.
Balance
±5
Adjust the AC Balance up to 5% above or below the calculated value.
AC Frequency
50-250Hz
Adjust the frequency of the AC waveform.
Mix AC/DC %
0-80%
Mixed AC/DC welding is the combination of TIG AC and TIG DC- in one weld. Mixed AC/DC gives you faster
welding speeds, better penetration, a faster weld puddle on cold workpieces, and allows you to weld on
thicker materials.
FusionPlus™
0-80%
FusionPlus is an advanced AC TIG feature that provides greater arc focus at high welding speeds, and
provides deep penetration even at low AC frequencies.
Diameter
1.0, 1.6, 2.0, 2.4, 3.2, 4.0
Optimises the welding arc ignition in AC TIG based on the chosen tungsten diameter.
DC Pulse
Setting
Values
Description
Pre-flow
0-20s
Set how long you would like your gas to flow before the arc ignites.
Start Amp
10-200A
Set the starting current when the arc ignites.
Up Slope
0-20s
Set how long it takes for the Start Amp to reach the Peak Amp.
Peak Amp
10-200A
Set the peak welding current.
Base Amp
10-200A
Set the base current of the pulse cycle.
Pulse Width
5-95%
Set the percentage of the pulse cycle spent in peak amp.
Frequency
0.5-999Hz
Set the number of pulses per second.
Down Slope
0-20s
Set how long it takes for the Peak Amp to reach the End Amp.
End Amp
10-200A
Set the End Amp to adjust how hot your weld will finish.
Post Flow
0-20s
Set how long you would like your gas to flow after the arc ends.
AC Pulse
Setting
Values
Description
Pre-flow
0-20s
Set how long you would like your gas to flow before the arc ignites.
Start Amp
10-200A
Set the starting current when the arc ignites.
Up Slope
0-20s
Set how long it takes for the Start Amp to reach the Peak Amp.
Peak Amp
10-200A
Set the peak welding current.
Base Amp
10-200A
Set the base current of the pulse cycle.
Pulse Width
5-95%
Set the percentage of the pulse cycle spent in peak amp.
Frequency
0.5-999Hz
Set the number of pulses per second.
Down Slope
0-20s
Set how long it takes for the Peak Amp to reach the End Amp.
End Amp
10-200A
Set the End Amp to adjust how hot your weld will finish.
Post Flow
0-20s
Set how long you would like your gas to flow after the arc ends.
Balance
±5
Adjust the AC Balance up to 5% above or below the calculated value.
AC Frequency
50-250Hz
Adjust the frequency of the AC waveform.
Diameter
1.0, 1.6, 2.0, 2.4, 3.2, 4.0
Optimises the welding arc ignition in AC TIG based on the chosen tungsten diameter.
3. Advanced TIG Settings
DIGITAL SCREEN - TIG
18
Содержание Xcel-Arc MULTI 230 AC/DC
Страница 2: ...2 ...
Страница 71: ...NOTES 71 ...