2
razberi™ Technologies
Safety Warning
Retain and follow all safety and operating instructions. Observe all warnings on products. Unplug the product from the
electrical outlet and discontinue use under the following conditions: The power cord or plug is damaged; the product is
exposed to liquid; the product is dropped or an object falls on the product; the product is noticeably overheated. Read this
manual carefully before installing the unit. Please read this manual first for correct installation and operation.
Never install the device on a ceiling that cannot hold its weight. The product may fall down and cause damages. Never
install the product near electric or magnetic fields. Install the device away from TVs, radio transmitters, magnets, electric
motors, transformers, and audio speakers since the magnetic fields distort the video image. Never install or use the product
in areas exposed to water, oil, or gas. The water, oil, or gas may result in operation failure, electric shock, or fire. Do not use
this unit near water (e.g., near a bath tub, wash bowl, kitchen sink, laundry tub, wet basement, swimming pool, unprotected
outdoor installation, or any area which is classified as a wet location). Never face the unit toward the sun. Direct sunlight
may cause fatal damage to sensors and internal circuits. Touching a wet power cord with hands or touching the power cord
with wet hands may result in electric shock.
Do not service any product yourself. Opening or removing covers that are marked with warning symbols or labels may
expose you to electric shock. Service needed on components inside these compartments should be done by an authorized
service provider. Replace any batteries with the equivalent battery type. Failure to do so may cause damage or bodily injury.
There is a danger of explosion if batteries are incorrectly replaced. Dispose of all used batteries according to the
manufacturer’s instructions.
Install the system in an environment where the ambient temperature does not exceed the maximum rated ambient
temperature of the rack mount system. Ensure there are no obstructions to the case ventilation. Blocking any of the built-in
airflow may cause overheating. The product must be connected to a circuit with an adequate rating to prevent an over-
current condition on the circuit. Slots in the product are provided for ventilation and should never be blocked or covered
since these protect it from overheating. The openings should never be blocked by placing the product on a flexible surface.
The product should not be placed in a built-in apparatus unless the apparatus has been designed to accommodate the
product, proper ventilation is provided for the product, and the product instructions have been followed.
Operate the product only from the type of power source indicated on the product’s electrical ratings label. If you have
questions about the type of power source to use, contact your authorized service provider. The power outlet for the power
cord should be easily accessible and located as close to the equipment operator as possible. When you need to disconnect
power to the equipment, unplug the power cord from the electrical outlet. When disconnecting a power cord/cable from an
outlet, pull on the connector. Never pull on the cable itself to disconnect from the power source. Handle all equipment with
care when disconnecting from the product or the power source. Equipment may be hot. The power cord must be properly
rated for the product and for the voltage/current marked on the product’s electrical ratings label. The voltage/current rating
of the cord should be greater than the voltage/current rating marked on the product. Do not overload an electrical outlet,
power strip, or convenience receptacle. Use care when moving products to other countries with different voltage standards.
Substitution for the power supply may result in destruction of the product or personal injury.
Unplug the product from the wall outlet prior to cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning. Never insert a foreign object into the product’s openings or ventilation slots. The product should be placed
away from radiators, heat registers, stoves, or other pieces of equipment (including amplifiers) that produce heat. Allow
sufficient air circulation around the product and power supply during use to ensure adequate cooling of the device. Prevent
direct exposure to radiant heat sources. Contact the provider if replacement parts are required. Use only the parts,
upgrades, and options sent from the provider.
© 2012 razberi™ Technologies; v3.02.12
All rights reserved. razberi™ Technologies makes no warranty of any kind with regard to this material,
including but not limited to the documentation, function, and performance of these programs and their
suitability for any purpose. razberi™ Technologies shall not be liable for any errors contained herein for
incidental or consequential damages in connection with the use of this material. This document contains
proprietary information protected by copyright. No part of this document may be reproduced without prior
consent of razberi™ Technologies.
Содержание MP Series
Страница 1: ...razberiTM MP Series User Manual ...
