background image

 

41 

 

WARRANTY 

 

RAYPAK WATER HEATER WARRANTY – AUSTRALIA ONLY 

WARRANTY CONDITIONS 

1.  This warranty is applicable only to water heaters 

manufactured from 1st May 2008. 

2.  The water heater must be installed in accordance 

with the Raypak water heater installation 
instructions, supplied with the water heater, and 
in accordance with all relevant statutory and local 
requirements of the State in which the water 
heater is installed. 

3.  Where a failed component or water heater is 

replaced under warranty, the balance of the 
original warranty period will remain effective. The 
replaced part or water heater does not carry a 
new warranty. 

4.  Where the water heater is installed outside the 

boundaries of a metropolitan area as defined by 
Rheem or further than 25 km from a regional 
Rheem branch office, or an Accredited Service 
Agent, the cost of transport, insurance and 
travelling costs between the nearest Rheem 

Accredited Service Agent’s premises and the 
installed site shall be the owner’s responsibility. 

5.  Where the water heater is installed in a position 

that does not allow safe, ready access, the cost 
of accessing the site safely, including the cost of 
additional materials handling and 

or safety 

equipment, shall be the owner’s responsibility. 

6.  The warranty only applies to the water heater 

and original or genuine (company) component 
replacement parts and therefore does not cover 
any plumbing or electrical parts supplied by the 
installer and not an integral part of the water 
heater, e.g. pressure limiting valve; isolation 
valves; non-return valves; electrical switches; 
pumps or fuse. 

7.  The water heater must be sized to supply the hot 

water demand in accordance with the guidelines 
in the Rheem water heater literature. 

 

WARRANTY EXCLUSIONS 

1.  REPAIR AND REPLACEMENT WORK WILL BE CARRIED OUT AS SET OUT IN THE RAYPAK WATER 

HEATER WARRANTY, HOWEVER THE FOLLOWING EXCLUSIONS MAY CAUSE THE WATER HEATER 
WARRANTY TO BECOME VOID AND MAY INCUR A SERVICE CHARGE AND / OR COST OF PARTS. 

a)  Accidental damage to the water heater or any 

component, including: Acts of God; failure due to 
misuse; incorrect installation; attempts to repair 
the water heater other than by a Rheem 
Accredited Service Agent or the Rheem Service 
Department. 

b)  Where it is found there is nothing wrong with the 

water heater; where the complaint is related to 
excessive discharge from the temperature and / 
or pressure relief valve due to high water 
pressure; where there is no flow of hot water due 
to faulty plumbing; where water leaks are related 
to plumbing and not the water heater or water 
heater components; where there is a failure of 
gas, electricity or water supplies; where the 
supply of gas, electricity or water does not 
comply with relevant codes or acts. 

c) Where the water heater or water heater 

component has failed directly or indirectly as a 

result of: excessive water pressure; excessive 
temperature and 

or thermal input; blocked 

overflow / vent drain; corrosive atmosphere; ice 
formation in the pipe work to or from the water 
heater. 

d)  Where the water heater is located in a position 

that does not comply with the Raypak water 
heater installation instructions or relevant 
statutory requirements, causing the need for 
major dismantling or removal of cupboards, 
doors or walls, or use of special equipment to 
bring the water heater to floor or ground level or 
to a serviceable position. 

e)  Repair and / or replacement of the water heater 

due to scale formation in the waterways or the 
effects of corrosive water when the water heater 
has been connected to a scaling or corrosive 
water supply as outlined in the Owner’s Guide 
and Installation Instructions booklet. 

2.  SUBJECT TO ANY STATUTORY PROVISIONS TO THE CONTRARY, THIS WARRANTY EXCLUDES ANY 

AND ALL CLAIMS FOR DAMAGE TO FURNITURE, CARPETS, WALLS, FOUNDATIONS OR ANY OTHER 
CONSEQUENTIAL LOSS EITHER DIRECTLY OR INDIRECTLY DUE TO LEAKAGE FROM THE WATER 
HEATER, OR DUE TO LEAKAGE FROM FITTINGS AND / OR PIPE WORK OF METAL, PLASTIC OR 
OTHER MATERIALS CAUSED BY WATER TEMPERATURE, WORKMANSHIP OR OTHER MODES OF 
FAILURE. 

Содержание B0109












































Отзывы: