Raypak B0109 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 43

background image

Notice to Victorian Customers from the

Victorian Plumbing Industry Commission

This water heater must be installed by a licensed person as required by

The Victorian Building Act 1993

Only a licensed person will give you a Compliance Certificate, showing that the work complies
with all the relevant standards. Only a licensed person will have insurance protecting their
workmanship for 6 years. Make sure you use a licensed person to install this water heater and
ask for your Compliance Certificate.

Warning:

Upon completion of the installation and commissioning of the water heater, leave

this guide with the householder or a responsible officer.

DO NOT

leave this guide inside of the

cover of the water heater, as it may interfere with the safe operation of the water heater or ignite
when the water heater is turned on.

PATENTS

This water heater may be protected by one or more patents or registered designs.

® Registered trademark of Rheem Australia Pty Ltd.

™ Trademark of Rheem Australia Pty Ltd.

Date of installation:

Model Nº:

Serial Nº:

Installed by:

Purchased from:

«
1
2
3
4
...
»

Содержание B0109












































Отзывы:

Нет отзывов

Похожие инструкции для B0109

Бренд: Eastern Tabletop Страницы: 19

Бренд: Jandy Страницы: 108

Бренд: Jandy Pro Series Страницы: 40

Бренд: Lasko Страницы: 4

Бренд: S&P Страницы: 36

Бренд: S&P Страницы: 16

Бренд: Paloma Страницы: 28

Бренд: Dantherm Страницы: 12

Бренд: UNITED Страницы: 8

Бренд: DAXOM Страницы: 20

Бренд: salmson Страницы: 195

Бренд: Tactical Страницы: 4

BlackFin CT-2902BPHP

Бренд: Panduit Страницы: 68

Under Desk Heater

Бренд: Warmly Yours Страницы: 6

Бренд: True Source Страницы: 27

BioPressure II 6000

Бренд: ubbink Страницы: 64

Бренд: Wacker Neuson Страницы: 52

Бренд: Q-Pumps Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды