Raypak B0109 Скачать руководство пользователя страница 36

Страница: 36 / 43

TEMPERATURE CONTROL

147 Hi/Low Models (CTX Thermostat)

Set Point Adjustment:

•

Press the ‘set’ button,

SE.1 will be displayed for twelve (12) seconds.

•

Press the ‘set’ button again,

The current set point value will be displayed.

•

Press the down button (

▼

/PRG) to decrease the set point or the up button (

▲

ALM) to increase the set point.

•

Once the required set point is selected, press the ‘set’ button to save the setting,

SE.1 will be re-displayed for twelve (12) seconds.

•

Press the up button (

▲

ALM),

SE.2 will be displayed.

•

Press the ‘set’ button,

The current set point for Low Fire will be displayed.

•

Press the down button (

▼

/PRG) to decrease the set point or the up button (

▲

ALM) to increase the set point.

•

Once the required set point is selected, press the ‘set’ button to save the setting,

SE.2 will be re-displayed

•

Wait 12 seconds,

The current temperature in the water heater will now be displayed and programming complete.

The recommended set points for SE.1 and SE.2 are 82°C and 75°C respectively for a heating system. However, it
may be necessary to increase SE.2 if there is an unacceptable variation in room temperature.

Differential Adjustment:

•

Press and hold the down button (

▼

/PRG) for at least 5 seconds,

“‘E0” will be displayed.

•

Press the up button (

▲

/ALM) until “E5.1” (differential setting for SE1).is displayed

•

Press the ‘set’ button,

The current differential value will be displayed.

•

Press the down button (

▼

/PRG) to decrease the differential or the up button (

▲

/ALM) to increase the

differential. NOTE: The differential is adjustable from 1°C to 6°C.

•

Once the required differential is selected, press the ‘set’ button to save the setting,

“E5.1” will be re-displayed.

•

Wait 12 seconds,

The current temperature in the water heater will now be displayed and programming complete.

NOTES

•

To adjust the differential setting for SE2 repeat the ‘Differential Adjustment’ steps above however when

selecting the ‘E’ parameter press the up button (

▲

/ALM) until “E5.2” is displayed.

•

NOT

adjust any other parameter settings; this may cause the thermostat to malfunction.

Содержание B0109












































Результаты поиска

Содержание B0109

Отзывы:

Похожие инструкции для B0109

Бренды по названию

Популярные бренды

Raypak B0109, Руководство пользователя и инструкции по установке

Результаты поиска

Содержание B0109

Отзывы:

Похожие инструкции для B0109

Бренды по названию

Популярные бренды