22
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
Press and
release the
TTC button.
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
AUX
ANT
^^^^
AUX
ANT
AUX ANT
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
4
5
6
7
ST
OP
CLOSE
OPEN
Press and hold
the LEARN button
(LED will light).
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
Every press and release
of the STOP button
will add 5 seconds to
the Timer-to-Close.
Example: 30 second
TTC = 6 presses of the
STOP button.
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
Press and release
the TTC button to
exit programming
mode. The LED
will fl ash once per
5 seconds of timer
setting.
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
Press and
release the
TTC button.
3
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
AUX
ANT
^^^^
AUX
ANT
AUX ANT
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
4
5
6
7
ST
OP
CLOSE
OPEN
Press and
release the
LEARN button
(LED will light).
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
AUX
ANT
^^^^
AUX
ANT
AUX ANT
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
4
5
6
7
ST
OP
CLOSE
OPEN
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
AUX
ANT
^^^^
AUX
ANT
AUX ANT
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
6
7
ST
OP
CLOSE
O
PEN
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
AUX
ANT
^^^^
AUX
ANT
AUX ANT
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
6
7
ST
OP
CLOSE
O
PEN
SINGLE BUTTON REMOTE CONTROL
3-BUTTON REMOTE CONTROL TO OPERATE AS A WIRELESS 3-BUTTON CONTROL STATION
NOTE:
The feature will use 3 of the 20 memory channels in the operator.
TO ERASE ALL REMOTE CONTROLS
BASIC PROGRAMMING
1
Press and release
the LEARN button
(LED will light).
2
Repeat steps 1 and 2 for additional remote controls.
1
2
3
Press and hold
the LEARN button
(LED will light).
Press the desired
button on the logic
board (OPEN,
CLOSE or STOP).
Release both
buttons.
Press and hold the desired button of the remote
control until LED fl ashes rapidly, then release.
Repeat steps 1 through 3 to program additional buttons.
TIMER-TO-CLOSE (TTC)
TO PROGRAM
Begin with door in fully closed position.
Timer-to-Close feature enables the operator to close from the open limit after a preset time, adjustable from 5 to 60 seconds.
Requires LiftMaster Monitored Entrapment Protection (LMEP) device.
Built in 315 MHz radio receiver permits as many as 20 Security
✚
®
remote controls or dip switch remote controls in any combination.
1
2
4
1
2
3
TO VERIFY TIMER-TO-CLOSE (TTC) SETTING
The TTC will become active after completion of the next open cycle.
NOTE:
The LED does not indicate that timer is running.
Press and hold the button on the remote control
until the LED fl ashes rapidly, then release to
complete programming (LED will go out).
1
Press and hold the
LEARN button (over 5
seconds) until the
LED goes out. All
programmed remote
controls will be
erased.
D14
COM
INTRLK
STOP
LED
OPEN
CLOSE
TTC
LEARN
1
LMEP1
LMEP2
2
3
45
67
ST
OP
CLOSE
OPEN
R27
Press and release the TTC button a
second time. The LED will fl ash once
per 5 seconds of timer setting.
To prevent possible SEVERE INJURY or DEATH:
• Install a LiftMaster Monitored Entrapment Protection (LMEP)
device.
• NEVER permit children to operate or play with door control
push buttons or remote controls.
• Activate door ONLY when it can be seen clearly, is properly
adjusted and there are no obstructions to door travel.
• ALWAYS keep door in sight until completely closed. NEVER
permit anyone to cross the path of closing door.
WARNING
REMOTE CONTROLS
