background image

Chapter 3: Advanced Operation

21

• Waypoint advance is requested by pressing 

track 

for 1 second in

Track mode (SeaTalk Navigators only).

• When the Man Overboard (MOB) function is activated in Track

mode.

When the alarm sounds, the pilot continues on its current heading, but
displays the bearing to the next waypoint and the direction in which the
boat will turn to take up that bearing.

Check that it is safe to turn onto the new track, and press

 

track 

to

accept the waypoint advance.

Alternatively, to cancel the alarm without accepting the waypoint
advance, press

 

standby 

to return to hand steering, or 

auto 

to return to

Auto mode.

Note:

 

The waypoint advance will only operate on pilots receiving

valid bearing to waypoint and waypoint number information.

Low battery

LOW BATT

The Low Battery alarm sounds when the supply voltage drops below
10 V (±0.5 V).

Press

 

STANDBY 

to clear the alarm and return to hand steering.

Start the engine to recharge the battery.

Watch alarm

WATCH

The Watch alarm is activated in Watch mode when the timer reaches 4
minutes. It is not available from Standby mode.

If you wish to set the Watch mode, the 

WATCH 

screen must be

configured as one of the Data Pages for display, as described in
section 

4.1

.

To set and control the Watch alarm:

1.

Select Auto, Track or Vane mode.

2.

Press the

 

disp 

key until the 

WATCH 

Data Page is displayed.

132_4c03.p65

14/06/99, 10:33

21

Содержание ST5000+













































































































Отзывы: