background image

 Raymarine World Wide Warranty

III

Raymarine UK Ltd.

APPLICABLE TO PRODUCT SOLD THROUGH OFFICIAL RAYMARINE UK LTD. DEALERS, DISTRIBUTORS AND BOAT 
BUILDERS WITHIN EUROPE, THE MIDDLE AND FAR EAST, AFRICA AND AUSTRALASIA.

Limited Warranty

The Raymarine warranty terms and conditions as described below do not affect the customers legal rights and 
complies with EU Directive 1999/44/EC.
In order to ensure that the product continues to operate efficiently and reliably, we recommend that, before using the 
product, the customer carefully reads the Owner’s Handbook and follows the advice on the safe and correct 
operation and use of the product. We recommend that the Raymarine product is installed by a Raymarine certified 
installer. Installation by persons other than a Raymarine certified installer may invalidate the warranty.

1. Product warranty

1.1 Raymarine warrants each new product to be of good materials and workmanship. Raymarine, or its approved 
agents, will repair or exchange under warranty any parts or product proven to be defective in material or 
workmanship under normal use, for a period of 2 years (24 months) from date of sale to end user, subject to the limits 
contained in this warranty document.
1.2 The Raymarine warranty covers the parts and labour associated with any warranty repair as described above, 
provided that the product is returned to Raymarine or one of its approved agents.
1.3 Raymarine reserve the right to replace under warranty, not repair, certain Raymarine products subject to the 
limitations below, provided that they are returned to the nearest Raymarine National Distributor. For details of such 
products refer to the internet at 

www.raymarine.com  or contact your nearest Raymarine National Distributor.

2. Onboard warranty

2.1 In addition to the Product warranty cover as described above, Raymarine will, authorize onboard warranty service 
by the nearest Raymarine approved service agent, subject to the maximum mileage and other limits referred to in 
paragraph 4.12 below, on products, where proof of installation, or commission by Raymarine certified installers, can 
be shown.
2.2 The warranty provides for onboard repair or exchange of the product, by Raymarine or its approved service 
agents, for a period of 2 years (24 months), subject to the limits contained in this warranty document. In the case of a 
product installed, by a Raymarine certified OEM installer, on a new boat prior to the sale of the boat to a customer, the 
2-year period will begin on the date of the sale of the boat to the customer. In the case of a product installed, by a 
Raymarine certified installer, on a boat already in the possession of the customer, the 2-year period will begin on the 
date of the commissioning of the installed product.
2.3 Certain Raymarine products are not covered by onboard warranty unless the products are pre-registered and on 
board warranty is purchased from the Raymarine certified installer. For details of such products refer to the internet at 
www.raymarine.com  or contact your nearest Raymarine National Distributor.
2.4 The Purchaseable onboard warranty is subject to the limitations below.

3.Obtaining warranty service

3.1 In the event of warranty service being required, the customer should contact Raymarine Technical Support or the 
nearest Raymarine approved service agent - the contact details of Raymarine Technical Support and a full list of the 
names and details of worldwide service agents are available on the internet at 

www.raymarine.com and in the 

Owner’s Handbook.

87063_1.book  Page III  Monday, December 19, 2005  3:22 PM

Содержание Mk II





























Отзывы: