Raycus RFL-C4000XZ Скачать руководство пользователя | Manualshive

Страница: 4 / 77

background image

Wuhan Raycus Fiber Laser Technologies Co., Ltd.

User Guide of RFL-C4000XZ~12000XZ

7 RS232 and INTERNET communication command........................................ 40

7.1 Port Configuration....................................................................................................40
7.2 Laser Communication Protocol (Network Port & Serial Port)............................... 41

8 PC software instructions.................................................................................... 45

8.1 Maininterface of PC software.................................................................................. 45
8.2 Multi-laser control area............................................................................................46

8.2.1 Add/delete laser............................................................................................... 47
8.2.2 ModifylaserIP...................................................................................................48

8.3 Main working status display.................................................................................... 48

8.3.1 Laser’s cumulative operating time display area..............................................49
8.3.2 Laserworkingstatusdisplayarea........................................................................49
8.3.3 Laser power-up, mode selection, light-out control area..................................51
8.3.4 Programming mode test area........................................................................... 51
8.3.5 Power slow rise&down parametersettingarea.................................................52
8.3.6 Laser output parameters read the settings area................................................52

8.4 Laserparameterdisplayarea.......................................................................................53
8.5 Alarm type display area........................................................................................... 53
8.6 PC softwareoperatingmodeselection........................................................................53
8.7 LanguageDisplays laser’s all status and parameters for diagnosis purposes..........55
8.8 Authorization (time-limited locking).......................................................................55

8.8.1 Authorization in user mode............................................................................. 55
8.8.2 Authorization in authorization mode............................................................56

8.9 About........................................................................................................................ 57
8.10 XP1 interface status indication (in diagnostic mode)............................................58
8.11 Log (in diagnostic mode)....................................................................................... 59

8.11.1 Download log.................................................................................................60
8.11.2 Downloadrecord of historicalfault.................................................................60
8.11.3 Downloaded file address................................................................................61

«
...
2
3
4
5
6
...
»

Содержание RFL-C4000XZ














































































Отзывы:

Нет отзывов

Похожие инструкции для RFL-C4000XZ

Бренд: GARANT Страницы: 239

Бренд: p-light Страницы: 36

Бренд: IDEAL Страницы: 12

Бренд: LA Audio Страницы: 9

Бренд: Guyatone Страницы: 2

Бренд: Ekinex Страницы: 37

Бренд: HMS Страницы: 36

Бренд: Pixlip Страницы: 15

MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE

Бренд: Kurzweil Страницы: 91

Бренд: schmersal Страницы: 20

Alcotest 7410 GLC

Бренд: Dräger Страницы: 15

Бренд: enz Страницы: 40

A3x-01 Ascent Trainer

Бренд: Matrix Страницы: 69

T 25 digital ULTRA-TURRAX

Бренд: IKA Страницы: 140

Бренд: Eaton Страницы: 2

Бренд: ABS Страницы: 12

Бренд: Boxym Страницы: 49

Бренд: Nagman Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды