Raycus RFL-C4000XZ Скачать руководство пользователя

Страница: 57 / 77

Wuhan Raycus Fiber Laser Technologies Co., Ltd.

User Guide of RFL-C4000XZ~12000XZ

Figure 34 A diagram of the laser's main display area

Table 13 The laser main display content and meaning

Display

Meaning

Output power

current setting percentage of power in real time

Output power

Average laser output power in real time

（

）

Laser temperature

Water cooling temperature in real time

（℃）

Power light

Status of main power supply:green-main power supply is on,
gray-main power supply is off

Ready light

Indicates readyness of current laser:green-laser is ready,gray-laser is not ready

Alarm light

indicates alarm status of current laser:yellow- laser is abnormal,
gray-laser is normal

Emission light

indicates the working model of the current laser

：

red-laser is in working model
gray-laser is not in output model

8.3.1 Laser’s cumulative operating time display area

The laser’s cumulative operating time display is shown in Figure 35. The cumulative start-up time,

cumulative laser output time, today's power-on time and today's lighting time can be displayed in hours,
minutes and seconds respectively.

Figure 35 Laser cumulative operating time display interface

8.3.2 Laserworkingstatusdisplayarea

The laser working status display area is as Figure 36, Table 14.

Содержание RFL-C4000XZ














































































Результаты поиска

Содержание RFL-C4000XZ

Отзывы:

Похожие инструкции для RFL-C4000XZ

Бренды по названию

Популярные бренды

Raycus RFL-C4000XZ, Руководство пользователя

Результаты поиска

Содержание RFL-C4000XZ

Отзывы:

Похожие инструкции для RFL-C4000XZ

Бренды по названию

Популярные бренды